Near boiling hot water dispensers with stainless steel tanks and flow is controlled via float switch. Maximum working pressure 3 Bar. Maximum operating temperature 98°C.

Section:

1380 Heaters

Section Subtitle:

Electric, thermal storage, mains fed, closed outlet. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within with system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

241202719

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

3/8” BSP M inlet/outlet

Marking:

Alfred Victoria "crown" logo on front of body. Model and product info on label on rear of body.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

F104M

Approval Holder:

ALFRED VICTORIA LIMITED

Company Name

ALFRED VICTORIA LIMITED

Postcode

B45 9AL

View All Listings by this Company

Range of ultrasonic water meters with brass bodies and EPDM O-rings. The inlets incorporate a double check valve assembly, verified by test - suitable for backflow protection against Fluid Category 3. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Huizhong logo, Model No, DN, CR and product info on face. CR and flow arrow on body.

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

SCL-61H-100 DN25: ¾” BSP (M) DN40: ¾” BSP (M)

Approval Holder:

Huizhong Instrumentation Co., Ltd.

Company Name

Huizhong Instrumentation Co., Ltd.

Address

No. 126 West Gaoxin Road, High‐Tech Industrial Development Zone, Tangshan City, Hebei Province

Country

China

View All Listings by this Company

Range of ultrasonic water meters with brass/plastic bodies. The inlets incorporate plastic strainers and brass spherical ball valves. Maximum working pressure 16.0 bar. Maximum operating temperature 50⁰C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

BSP M x M connections: DN15 – ½” BSP, DN20 – ¾” BSP, DN25 – 1” BSP, DN32 – 1 ¼” BSP, DN40 – 1 ½” BSP.

Marking:

Flow arrow on plastic body and brass inlet outlet tube, manufacturers logo, barcode, size and technical data under digital display cover.

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

UWM2401 - DN15, DN20, DN25, DN32 & DN40.

Approval Holder:

Elite Experts Industry Company (EEICo).

Company Name

Elite Experts Industry Company (EEICo).

Address

View All Listings by this Company

Range of ultrasonic water meters with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85⁰C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN32 - 1 ¼” BSP, DN40 - 1 ½” BSP, DN50 - 2” BSP.

Marking:

Manufacturers logo, flow arrow, barcode, size and technical data on digital display cover.

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

U-WR2 (DN32, 40 & 50).

Approval Holder:

Viewshine Metering Ltd.

Company Name

Viewshine Metering Ltd.

Address

Building 6, Moganshan Road 1418-41 Hangzhou Zhejiang Province

Country

China

Phone

15267464630

General Email

xiongdong@viewshine.cn

View All Listings by this Company

Range of heat interface units providing heating and instantaneous hot water. The central heating and hot water is generated via plate heat exchangers. The central heating circuit contains a pressure relief valve (3.0 bar) and an expansion vessel. Max Temperature & Pressure: Primary Circuit: 6.0 bar at 90°C DHW Circuit: 10.0 bar at 55°C Secondary Circuit 6.0 bar at 90°C

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

3/4" BSP (F) captive nut connections

Marking:

Baxi on front cover, Baxi, product info on label on front cover

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

A/7892284 AquaHeat HD/HWI 12/50 with Heat Meter & Mercurius B/7892283 AquaHeat HD/HWI 12/50

Manufacturer:

Baxi Heating UK Limited

Company Name

Baxi Heating UK Limited

Address

Brooks House, Coventry Road, Warwick

Postcode

CV34 3LL

View All Listings by this Company

Range of shock arrestors with a stainless-steel body and EPDM liner. The compression connection of the X2041.015 model is for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

X2041.015: 15mm compression, X2040.G15: ½” BSP (M).

Marking:

Zhejiang Fansheng Fluid Control Co., Ltd logo on body

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

X2041.015, X2040.G15.

Approval Holder:

Zhejiang Fansheng Fluid Control Co., Ltd.

Company Name

Zhejiang Fansheng Fluid Control Co., Ltd.

Postcode

317605

Country

China

Phone

+86 576 8746 0061

General Email

info@IVANCI.com

View All Listings by this Company

Shock arrestors with a copper body, plastic shuttle and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

WHA-G12M-LL: ½” BSP (M), WHA-G34M-LL: ¾” BSP (M), WHA-G1M-LL: 1” BSP (M), WHA-AM-LL: ½” NPT (M), WHA-BM-LL: ¾” NPT (M), WHA-CM-LL: 1” NPT (M).

Marking:

Yongtong logo, Yongtong, part # (model), size (A, B or C), water hammer arrestor, WRAS and made in China on adhesive label on body.

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

WHA-G12M-LL: 1/2” G Male Water Hammer Arrester, A, WHA-G34M-LL: 3/4” G Male Water Hammer Arrester, B, WHA-G1M-LL: 1” G Male Water Hammer Arrester, C, WHA-AM-LL: 1/2” MIP Water Hammer Arrester, A, WHA-BM-LL: 3/4” MIP Water Hammer Arrester, B, WHA-CM-LL: 1” MIP Water Hammer Arrester, C.

Approval Holder:

Taizhou Yongtong Brass Industry Co., Ltd.

Company Name

Taizhou Yongtong Brass Industry Co., Ltd.

Address

50 Keyuanbei Road, Qinggang, Yuhuan, Zhejiang

Country

China

Phone

+86 0576-87105707

General Email

j.luo@yongtongbrass.com

View All Listings by this Company

Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. Maximum operating temperature 35°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250702722

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

U3, U5, P3 or P5: 1” BSP (F) inlet x 1” BSP (F) outlet. U7 or P7: 1¼” BSP (F) inlet x 1” BSP (F) outlet. U9 or P9: 1½” BSP (F) inlet x 1¼” BSP (F) outlet. U18 or P18: 2” BSP (F) inlet x 1½” BSP (F) outlet.

Marking:

Ultra Models: Pentax logo and other technical data on data plate on body. Plus Models: Foras logo (brand of Pentax SpA) and other technical data on data plate on body

Installation Requirements:

R001 R415

Expiry date:

31/07/2030

Proviso:

The discharge from the drain plug must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717.

Model:

ULTRA range: U 3 – XX/Y, U 5 – XX/Y, U 7 – XX/Y, U 9 – XX/Y, U 3 – XX/Y T, U 5 – XX/Y T, U 7 – XX/Y T, U 9 – XX/Y T, U 18 – XX/Y T. PLUS range: P 3 – XX/Y, P 5 – XX/Y, P 7 – XX/Y, P 9 – XX/Y, P 3 – XX/Y T, P 5 – XX/Y T, P 7 – XX/Y T, P 9 – XX/Y T, P 18 – XX/Y T. Where: U or P = model type. U = ULTRA, P = PLUS. 3/5/7/9/18 = nominal flow rate in m³/h. XX = nominal power HPx100. U3 or P3 (single or three phase): 50-150. U5 or P5 (single or three phase): 70-200. U7 or P7 (single phase): 100-300. U7 or P7 (three phase): 100-350. U9 or P9 (single or three phase): 100-250. U18 or P18 (three phase only): 180-400. Y = Number of impellers. U3, U5, P3 or P5 (single or three phase): 2-7 stages. U7 or P7 (single phase): 2-6 stages. U7 or P7 (three phase): 2-7 stages. U9 or P9 (single or three phase): 2-5 stages. U18 or P18 (three phase only): 2-4 stages. Blank or T = motor: blank = single phase, T = 3 phase

Approval Holder:

PENTAX INDUSTRIES SpA

Company Name

PENTAX INDUSTRIES SpA

Address

Viale dell’Industria 1 Veronella

Postcode

37040

Country

Italy

Phone

+39 0442 489567

General Email

g.cengia@pentax-pumps.it

View All Listings by this Company

Manufacturer:

PENTAX INDUSTRIES SpA

Company Name

PENTAX INDUSTRIES SpA

Address

Viale dell’Industria 1 Veronella

Postcode

37040

Country

Italy

Phone

+39 0442 489567

General Email

g.cengia@pentax-pumps.it

View All Listings by this Company

A range of variable speed booster pumps with stainless steel bodies and impeller. Maximum working pressure: 8 bar. Maximum operating temperature: 35°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250708701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1” BSP (F) x 1” BSP (F).

Marking:

Calpeda and logo on adhesive label located on the pump’s inverter cover.

Installation Requirements:

R001 R415

Expiry date:

31/07/2030

Model:

MÈTA - Single pump variable speed pressure boosting system with integrated control, 1.35kW, nominal speed n=4500rpm, IPX4. MÈTA SMALL - Single pump variable speed pressure boosting system with integrated control, 0.65kW, nominal speed n=5800rpm, IPX4. MÈTA-2 - Single pump variable speed pressure boosting system with integrated control, 1kW, nominal speed n=5800rpm, IPX4.

Approval Holder:

Calpeda S.p.A

Company Name

Calpeda S.p.A

Address

Via Roggia Di Mezzo 39 36050 Montoro Vicentino Vicenza

Country

Italy

View All Listings by this Company

Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 2.0 bar (MS(s) models), 4.0 bar (AM(E) models) Maximum operating temperature 85°C

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241102725

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

TERAL, model, size & technical information on date label on body. Flow arrow on cover.

Installation Requirements:

R001 R415

Expiry date:

30/11/2029

Model:

MS(m)XXX-XX-E 1.m: different phase. --m: single phase, none: three phases 2.XXX: Rated flow (L/min) 3.XX: Rated power(kW). 4.E: E type end connection mode and size -- Rated flow(70-120m3/h): G1¼"XG1" -- Rated flow(210m3/h): G1½"XG1¼" -- Rated flow (370 m3/h): G2"XG1¼ AM(E) XXxXX (B) X/X-X XX(S) 1. E: Intelligent Type 2. XX: Inlet diameter (mm), range: 25,32,40,50 mm. 3. XX: Outlet diameter (mm), range: 25,32,40,50 mm. 4. B: alternative pump group 4. X/X: number of impeller /number of smaller impeller (if any) 5. X: motor frequency 6. XX: Rated power(kW) 7. S: different phase (S: single phase, none: three phases.)

Manufacturer:

Teral Asia Ltd

Company Name

Teral Asia Ltd

Address

Room 1001 10/F, Olympia Plaza, 255 Kings Road, North Point

Country

Hong Kong

View All Listings by this Company