'COD.2011'. Black coloured, injection moulded polypropylene compression fitting. For use with water up to 23°C.
'Thermocomp MB006SXP-BK1A994' (black coloured). Injection moulded polypropylene material. For use with water up to 85°C.
'DF201'. White coloured, extruded PTFE tape. For use with water up to 85°C.
'PTFE FE 1000'. White coloured, compression moulded PTFE material. For use with water up to 85°C.
'M-111 & M-139'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
'M-111'. White coloured, compression moulded PTFE material. For use with water up to 85°C.
'Filtren TM 25190, TM 25133, TM 25280 & TM 25450'. Blue coloured polyurethane foam manufactured by foaming and reticulation. For use with water up to 23°C.
'70 EPDM 291'. Black coloured, injection moulded EPDM rubber 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.51mm & 2.50mm. For use with water up to 85°C.
'EPOE7001P-WRC Diaphragm'. Black coloured, injection moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 1.20mm. For use with water up to 85°C.
'EPDM 1570'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 23°C.
'CE EPDM (TY-02-50) & CE EPDM (TY-05-80)'. Black coloured, compression moulded EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size between 0.75mm & 1.0mm. For use with water up to 23°C. From February 2024 the materials are for use with water up to 65°C.
‘EP70A9OF’. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.06mm For use with water up to 23°C.
'AA6KWZ, AA7KWZ, AA8KWZ and AA9KWZ'. Black coloured, compression moulded EPDM materials with a shore hardness of between 60 & 88. Tested in-radius size 1.0mm. AA6KWZ is for use with water up to 65°C. AA7KWZ, AA8KWZ and AA9KWZ are for use with water up to 23°C.
‘VF75GRN seals & ‘O’ rings’. Green coloured, injection moulded fluoroelastomer `O` rings & seals. Shore hardness 75. The ‘O’ rings have a tested in-radius size of 1.0mm. The seals have a tested in-radius size of 5.5mm. For use with water up to 85°C.
'3272 Washers & 'O' rings'. Green coloured, injection moulded FKM washers & 'O' rings. Shore hardness 70. The washers have a tested in-radius size of 0.75mm. The 'O' rings have a tested in-radius size of 1.31mm. For use with water up to 85°C.
SIL4010, SIL5010 & SIL6010 white translucent. SIL4010, SIL5010, SIL6010 & SIL7010 blue. SIL4010, SIL5010, SIL6010 & SIL7010 red. SIL4010, SIL5010, SIL6010 & SIL7010 yellow. Compression moulded silicone rubber materials. Shore hardness between 40 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
SIL4010, SIL5010 & SIL6010 white translucent. SIL4010, SIL5010, SIL6010 & SIL7010 blue. SIL4010, SIL5010, SIL6010 & SIL7010 red. SIL4010, SIL5010, SIL6010 & SIL7010 yellow. Compression moulded silicone rubber materials. Shore hardness between 40 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Berner Green Paste'. Green coloured, polymer sealing paste. Apply as per manufacturer's Technical Data Sheet '46845(P)', dated 'December 2019'. For use with water up to 85°C.
'RTP 0599 X 145641 BLACK'. Dark grey coloured, injection moulded, SAN material. For use with water up to 50°C.
Range of single hole, single outlet (swivel) electronically controlled tap assemblies. The flow and temperature is controlled by a ceramic cartridge headworks with single lever operating members. The flow is also controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The hose inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted taps for cold or premixed water with stainless steel bodies. Flow is controlled by a solenoid valve activated via an infra-red sensor, and the spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single hole, single outlet (fixed) tap assemblies (chromium plated brass) with a solenoid valve controlling the flow and activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connecting hose. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor and the temperature is controlled via a ceramic disc headwork with a dome type operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a single check valve assembly (verified by test suitable for backflow protection against Fluid Category 2) and the inlet incorporates a stainless-steel strainer. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a stainless-steel strainer prior to the solenoid. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted taps for cold or premixed water (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet hoses have stainless steel strainers and incorporate approved check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted tap assemblies for cold or premixed water with chromium plated brass bodies. Flow is controlled by a solenoid valve activated via an infra-red sensor and the spout outlets have plastic aerators. Supplied with stainless steel braided PEX lined connection hoses. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button and incorporates a angle valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted, single hole, single outlet (fixed), combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout has a waterfall outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of flushing valves (gunmetal body) which incorporate a screw down stop valve, spherical valve and air gap to drain. Maximum working pressure 10.0 bar. Cold water use only.
Range of aerators/flow regulators with chrome plated brass bodies, incorporating silicon seals. The products also incorporate either plastic (SB-STA ASQPQ 023A & SB-TA ASQPQ 011) or stainless-steel strainers (SB-ILFR). Open outlet use only.
Non-metallic materials and components comply with BS6920 at 85°C
Range of single hole, single outlet pull out spray, combination tap assemblies (brass bodies, various finishes – see models) incorporating ceramic cartridge headworks with single lever operating members controlling the hot and cold and a quarter turn ceramic disk headwork with a dome type operating member controlling chilled water supply. The spout outlet incorporates a plastic aerator. The inlet from the tap to the pull-out spray hose incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Model 32 020 000 is supplied with a pop-up waste. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate plastic flow straighteners or aerators. The products are supplied with approved click type wastes, verified by test. . Maximum working pressure - 5.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass), T-638-series incorporates quarter turn ceramic disc headworks with single lever operating members T-638M series incorporates, non-rising spindle headworks with dome or cross-top operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with a lever operated pop-up waste. Maximum working pressure 10.0 bar. Max operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener (TR1025 and TR1026 models) or a plastic aerator (all other models). The products are supplied with or without a click type pop-up waste (see model). Maximum operating pressure: MINI models 10.0 bar, all other models 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet fixed combination tap assemblies (brass bodies, various finishes – see models). TSA models incorporate quarter turn ceramic disc headworks with cross-top operating members. TDA models incorporate a ceramic cartridge headworks with a single lever operating member. The spout outlets incorporate plastic aerators. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assembly (various finishes, see models), incorporating ceramic cartridge headworks with single lever operating members. The products incorporate self-cancelling diverters to shower outlets and plastic aerators in the spouts. Not supplied with hose and handset. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies (chrome and ‘supersteel’ plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The tap also incorporates a quarter turn ceramic disc headwork with a dome type operating member controlling the filtered water outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, metal, single outlet (swivel) combination tap assemblies (various finishes), incorporating a ceramic disc headwork controlling the temperature with a single lever operating member and a push on/off button cartridge controlling the flow. The spout outlet incorporates a plastic aerator. Supplied with a lever pop up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, metal, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headwork with single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headwork and single lever operating member. The spout outlets incorporate a plastic aerator. A pop-up waste is also supplied. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel), combination tap assemblies (brass bodies with various finishes), incorporating ceramic cartridge or quarter turn ceramic disc headworks with single lever, cross-top or dome operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 or 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Floor mounted single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. This product is supplied with shower hose, shower handset and PEX inner-lined braided inlet hoses. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Page 57 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
