Range of bedpan washing & disinfection machines. The flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure - See models Maximum operating temperature - 90 °C

Section:

2360 Washing Machines

Section Subtitle:

Bedpan and disinfecting. Washing machines in this section will indicate the category of backflow prevention built into each appliance. The location and the use of the washing machine will determine any additional backflow protection that may be required.

WRAS Approval Number:

240102706

Size:

½” BSP (M)

Marking:

Stanbridge on control panel. Stanbridge, serial number and company information on date plate on front panel.

Installation Requirements:

R001

Expiry date:

31/01/2029

Model:

CS1 ST – 000101 – 4.14 Bar CS2 ST – 000-201 – 4.14 Bar CS3 ST – 000-301 – 4.14 Bar CS3 HD – 000-302 – 8.00 Bar Slimline – 000-401 – 8.00 Bar

Product Images

Approval Holder:

Stanbridge Ltd

Company Name

Stanbridge Ltd

Address

Unit 78, Powder Mill Lane Quester Estate Dartford

Postcode

DA1 1JA

Country

United Kingdom

Phone

+44 (0)1689 806500

General Email

claire@stanbridge.co.uk

View All Listings by this Company

Manufacturer:

Stanbridge Ltd

Company Name

Stanbridge Ltd

Address

Unit 78, Powder Mill Lane Quester Estate Dartford

Postcode

DA1 1JA

Country

United Kingdom

Phone

+44 (0)1689 806500

General Email

claire@stanbridge.co.uk

View All Listings by this Company

Range of commercial washing machines with flow controlled by solenoid valves and discharged via type AB air gap assembly (verified by test - suitable for backflow protection against fluid category 5). The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5 Bar. Maximum operating temperature 60°C.

Section:

2370 Washing Machines

Section Subtitle:

Clothes. Washing machines in this section will indicate the category of backflow prevention built into each appliance. The location and the use of the washing machine will determine any additional backflow protection that may be required.

WRAS Approval Number:

240102709

Size:

Stainless steel braided silicone lined flexible hose assemblies with 3/4" BSP captive nut end connections.

Marking:

Renzacci on front panel, Renzacci, model, product info on data plate on rear panel

Installation Requirements:

R001 R160

Expiry date:

31/01/2029

Model:

HS9, HS11, HS13, HS18, HS24, HS28, HS35 LX16, LX16 E-SPEED, LX22, LX22 E-SPEED, LX35, LX35 E-SPEED SX11, SX11 E-SPEED, SX14, SX14 E-SPEED, SX16, SX16 E-SPEED, SX22, SX22 E-SPEED, SX35, SX35 E-SPEED WB25, WB35 LX55, LX55 E-SPEED HS, LX, LX E-SPEED, SX, SX E-SPEED models are single door with front loading WB models are double door barrier with side loading. Models added December 2024 HS55, HS90, LX55, LX E-SPEED, LX70, LX70 E-SPEED, LX120, SX55, SX55 E-SPEED, WB70

Product Images

Approval Holder:

Renzacci SPA – Industria Lavatrici

Company Name

Renzacci SPA – Industria Lavatrici

Address

Via Morandi, 13 - 06012 Citta Di Castello PG Italy

View All Listings by this Company

Manufacturer:

Renzacci SPA – Industria Lavatrici

Company Name

Renzacci SPA – Industria Lavatrici

Address

Via Morandi, 13 - 06012 Citta Di Castello PG Italy

View All Listings by this Company

'ELECTROCOAT BP 1119'. Factory applied, black coloured Bituminous Paint. Apply as per manufacturer's TDS Document No: 'ECL/ TDS / BP-1119-Bituminous Paint', Issue Date '10-Aug-20', Version No: '01'. Cure for 12 minutes at 45°C, followed by 10 hours at 28°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5021 Bituminous Based Products

Section Subtitle:

Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials containing petroleum or asphaltic bitumen are not approved for use on water-retaining structures with large surface:volume ratio such as lining of pipes, cisterns or water storage tanks in contact with wholesome water, but may be acceptable for use where there is only a small surface area in contact with the water – e.g. taps, valves and pipe connectors.

WRAS Approval Number:

240255033

Expiry date:

28/02/2029

Approval Holder:

Electrosteel Castings Ltd.

Company Name

Electrosteel Castings Ltd.

Address

30 B.T. Road, PO Sukchar, District 24 Parganas (N) West Bengal, Kolkata - 700115

Country

743179

View All Listings by this Company

'Graphitar G-86' & 'Graphitar G-39'. Dark grey coloured, pressed and machined Carbon Graphite materials. For use with water up 85°C.

Section:

5022 Carbon

Expiry date:

31/03/2029

Approval Holder:

USG Gledco

Company Name

USG Gledco

Address

Leeds

Postcode

LS4 2JR

View All Listings by this Company

‘PRIMER NATZINC EP9015 SC PART A’ Primer for use with ' HYDRALFUN AC BLEU PAM RAL5005-CZL8190 ' top-coat. Factory applied, blue coloured (once applied) primer and finish-coat. Mix base:hardener of primer in a 100:10 weight ratio and apply as per manufacturer’s TDS February 2024. Then apply top-coat as per manufacturer’s TDS February 2024. Cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

240255035

Expiry date:

28/02/2029

Approval Holder:

Prospa

Company Name

Prospa

Address

4, RUE DU 43ème R.I.C 80510 LONGPRE LES CORPS SAINTS

Country

France

View All Listings by this Company