Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. The products are available as follows: Bronze body, bronze wedge and handwheel (ART 325RS & ART 330 HW ). Bronze body, bronze wedge and lock-shield (ART 330 LS). Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. Bronze body, bronze wedge and handwheel. Maximum working pressure 20.0 bar Maximum operating temperature 85°C.
Range of gate valves with a brass body and wedge. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. With Bronze body, bronze wedge and handwheel. Maximum working pressure 20.0 bar Maximum operating temperature 85°C.
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets with Bronze body, bronze wedge and handwheel Maximum working pressure 20.0 bar Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with brass or DZR brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Angled servicing valves with chrome plated brass bodies incorporating triangular type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of screw down stop valves with plastic bodies, NBR washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). For above and below ground use. Maximum working pressure 6 bar. Cold water use only.
Range of screw down stop valves with plastic bodies, NBR washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). For above and below ground use. Maximum working pressure 6 bar. Cold water use only.
Monobloc manifold containing an in-line pressure reducing valve (Adjustment Range between 2.7 and 3.3 bar, but factory pre-set at 3 bar) and a pre-set expansion relief valve (pre-set pressure 6 bar) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates also a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Inlets and outlets have compression connections, for use with copper pipe to EN1057. Maximum working pressure 12 bar. Maximum operating temperature 80°C.
'Iupital F10-EW'. White coloured, injection moulded POM material. For use with water up to 85°C.
'8284873 HA002I INT 100 HYF WHITE SN80'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's TDS 'Revision Date: V2, 24.05.2024', 'Region: EMEA'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SF-CM1'. Factory applied, grey coloured, sulphate resistant cement mortar. Mix cement mortar, sand & water in a 2:1:0.4 mass ratio and apply as per manufacturer's user instructions 'SF-CM1', 'Vision A1' dated '2024-7'. Cure for 12 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'C100E' & 'C100ELT'. Orange coloured ion exchange resins. For use with water up to 85°C.
'Latigloss 66 H2 G/50 Nat.:0003F2 (appears beige coloured) & Latigloss 66 H2 G/50 Black:3352F2 (black coloured)'. Injection moulded PA66 materials. For use with water up to 85°C.
Tecomid NA40 GR25 NL HS QF (white coloured) and Tecomid NG40 GR30 BK250 HS QW, Tecomid NA40 GR30 BK005 HY QH & Tecomid NA40 GR30 BK250 HY QW (black coloured). Injection moulded PA materials. Tecomid NA40 GR25 NL HS QF (white coloured) & Tecomid NG40 GR30 BK250 HS QW (black coloured) are suitable for use with water up to 85°C. Tecomid NA40 GR30 BK005 HY QH (black coloured) & Tecomid NA40 GR30 BK250 HY QW (black coloured) are suitable for use with water up to 23°C.
'Viega Raxofix, PE-RT/Al/PE-RT Multilayer Pipe'. Extruded, multi-layered pipe comprising of a black coloured PE-RT inner layer, aluminium middle layer and grey or white coloured PE-RT outer layer. For use with water up to 70°C.
Page 505 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
