Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The V23AR16 & F23AR25 models have a rising spindle, the V23A16 & F23A25 models have a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of in-line screw-down stop valves with brass bodies, incorporating rising spindle headworks and EPDM washers. For use with BS EN 1057 copper pipe. Maximum working pressure 16 Bar at 30°C, 5 Bar at 99°C
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of electrolytic water conditioning units consisting of stainless-steel tube with a copper/zinc alloy sacrificial anode and brass inlet and outlet connections. Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Ultra violet disinfection units consisting of a stainless steel body and quartz sleeve. Model WS-10-1206/3030031 Alde Aquaclear has a maximum working pressure of 5.0 bar and a maximum operating temperature of 40°C. All other models have a maximum working pressure of 7.0 bar and a maximum operating temperature of 60°C.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 8.3 bar. Cold water use only.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
'T195 NS sealing plate'. White coloured, compression moulded sealing plate. For use with water up to 85°C.
'T11 Sealing Ring'. Black coloured, compression moulded, ceramic sealing ring. For use with water up to 85°C.
'CER1' Ceramic Diaphragm'. White coloured ceramic diaphragm manufactured by casting. For use with water up to 85°C.
'Primgreen LAT 12035 & Unbrako wiscoat polyamide 11, ESY Blue 7265' coating system. Factory applied, blue coloured, polyamide powder coating system. Apply primer (Primgreen LAT 12035) and top coat (Unbrako wiscoat polyamide 11, ESY Blue 7265) as per user instructions ‘TSW/PR/02 REVISION A dated: 13.02.2012’. Cure both primer and topcoat for 12 minutes@215°C (each). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Apcoflor MFP 140 Primer and Smartcare Polyurea PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix Apcoflor MFP 140 Primer in a 1:1 mix ratio and apply as per Product Data Sheet ‘Version ‘0’, dated ‘Aug.2007’. Cure for 2 hours@25°C. Then mix and apply Smartcare Polyurea PW Coating as per Product Data Sheet ‘V01’, dated ‘8/2022’. Cure for 1 minute@25°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Clean Tech HPEC 1001(J) Grey'. Factory applied, two-part, grey coloured (once mixed) polyurethane coating. Mix Parts A & B in a 3:1 volume ratio and apply as per manufacturer's product datasheet 'CCPL/HPCCDN/SPL/20-21/5 /C/R11/PS/R3/90s/F', issue date '15.01.2021'. Cure for 7 days@30°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Endoprene 888.56'. Factory applied, beige coloured, two-part PU coating. Mix Parts A & B in a 75:25 volume ratio and apply as per Technical Data Sheet dated 09/12/2020. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Resicoat PI (HKH01R)'. Factory applied, green coloured epoxy powder coating. Pre-heat the substrate to 180°C and apply and cure in accordance with Product Datasheet dated August 11, 2022. Post-cure for 30 minutes@230°C. For use with water up to 85°C. This material is only approved for the pre-heat and post-cure conditions that appear on the approval. If the pre-heat and/or post-cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Rhenolub® MK I-RB FDA'. Factory applied, clear epoxy coating. Apply as per manufacturer's instructions 'version 1' dated 28.10.2022. Cure for 30 minutes@140°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Valve Green Powder Coating Pulver 010'. Factory applied, green coloured epoxy resin coating. Apply as per manufacturer's data sheet ‘FR.07.03.18 Rev. 01 08.03.2021', issued '30.03.2022'. Cure for 10 minutes@160°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'181019 Epoxy Phenolic RAL 5012'. Factory applied, blue coloured epoxy phenolic powder coating. Mix and apply as per manufacturer's instructions issued '15.01.2023'. Cure for 10 minutes at 200°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPL Gold Sulphate Resisting Portland Cement'. Factory applied, grey coloured Sulphate Resisting Portland Cement. Mix cement, sand and water in a 1.0:1.4:0.35 mass ratio and apply as per manufacturer's work instructions document code 'WI/SP/FINC&B/02', issue '06'. Cure for 24 hours at 27°C & 70% RH. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Endoprene 888.55'. Factory applied, two-component, beige coloured polyurethane coating. Mix and apply as per manufacturer's Data Sheet 'Doc. 089' dated '01/07/2011'. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic 840 ES'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet dated 16/05/2022. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Sika UAE L.L.C The authorization, training and certification of the local applicators are the responsibility of Sika UAE L.L.C and not the responsibility of WRAS.
‘Belzona 1341 available in Blue & Grey’. Site applied, two-component epoxy coatings consisting of a base and solidifier. Mix and apply as per manufacturer’s instructions for use ‘FN10139’, publication no. ’07-03-19’. Cure coat 1 for 4 hours at a temperature of between 10°C and 30°C. Cure coat 2 as per in accordance with ‘full mechanical loading or water in manufacturer’s instructions for use ‘FN10139’, publication no. ’07-03-19’. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`KA Tanking Slurry`. Site applied, grey coloured tanking slurry. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 1 as per manufacturer's IFU 'AFSOL001', dated '05/04/2022'. Cure for 24 hours@7°C. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 2, 24 hours after the first coat, as per manufacturer's IFU 'AFSOL001', dated '05/04/2022'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BÜFA®-ISO-Gelcoat 3000-H 572-9735 & Synolite 5410-P-4'. Grey coloured, unsaturated polyester gelcoat with a hand-laid unsaturated polyester resin and fibreglass laminate. Apply and cure in accordance with manufacturer's user guides 'Q-035, issue 1' & 'BUKUG 1001, issue 1' dated 19/08/2020. For use with water up to 23°C.
'Silicone Greases PH041, 665016-TUB, 665016, PHCB041, 665017 & ASG50'. White coloured silicone greases. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'F15220 Center Silicone Lubricant'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'OP-90601' (orange coloured) & 'IP-90604' (light orange coloured). Injection moulded polyester materials. For use with water up to 50°C.
‘Dura-Line HD100 B Pipe’. Black coloured (with blue stripes), extruded HDPE pipe. For use with water up to 60°C.
'NTG PE100 Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'Supreme PE Electrofusion Fittings'. Black coloured, injection moulded polyethylene (PE 100) electrofusion fittings. For use with water up to 65°C.
'DR-PLAST HDPE PE-100 Pipes'. Black coloured (with dark blue stripe), extruded HDPE pipe. For use with water up to 60°C.
'DR-PLAST HDPE PE-100 Fittings'. Black coloured, HDPE fittings manufactured by either injection moulding or butt fusion welding. For use with water up to 60°C.
'Aura HDPE Electrofusion Fittings'. Black coloured, injection moulded HDPE (PE100) electrofusion fittings. For use with water up to 65°C.
'Eltex TUB124N2025'. Blue coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex TUB171'. Black coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex Superstress TUB121N6000'. Black coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex TUB121'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'ELTEX Superstress TUB121N3000'. Black coloured, extruded polyethylene material. For use with water up to 23°C.
'Icorene 1314 BLK 9001'. Black coloured LLDPE material manufactured by rotomoulding. For use with water up to 85°C.
'RTP 0199 X 155521 Natural'. Natural (appears beige coloured), injection moulded polypropylene material. For use with water up to 50°C.
'TEADIT TF1590'. Pale orange coloured, PTFE material manufactured by mixing, calendaring, cutting and sintering. For use with water up to 85°C.
'STRONGHOLD SH-EP3'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘STRONGHOLD SH-EP5’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions rev. 1 dated 03/02/2022. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hongli IRHD 70'. Black coloured, press moulded EPDM material. Shore hardness 70. Tested in-radius size 1.09mm. For use with water up to 23°C.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
‘SBPEP4555 (50), SBPEP55 (55), SBPEP60 (60), SBPEP65 (65), SBPEP70 (70), SBPEP75 (75) & SBPEP7085 (80)’. Black coloured, compression moulded EPDM rubber sheet materials with a shore hardness of between 50 & 80. Tested in-radius size of 1.0mm. For use with water up to 60°C.
'E6083AA'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM C12251'. Black coloured, compression moulded, EPDM rubber material. Shore hardness 77. Tested in-radius size 12.5mm. For use with water up to 23°C.
'EP601289C'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
Page 50 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
