Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies and EPDM swing gates. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of full-bore spherical valves with bronze bodies, PTFE seats incorporating redox coated brass ball and various operating members (see models). Maximum working pressure 40 Bar Maximum operating temperature 95°C
Range of spherical valves incorporating a bronze body, brass or stainless-steel ball and single lever operating member. Maximum working pressure 25.0 bar.
Non-metallic materials and components comply with BS6920 at 82°C
Range of spherical valves incorporating a bronze body, brass ball and butterfly lever operating member. Maximum working pressure 25.0 bar.
Non-metallic materials and components comply with BS6920 at 82°C
Range of cast iron gate valves with blue epoxy coating, EPDM coated disc, PTFE gasket and EPDM seals. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Range of screw-down stop valves with brass bodies, incorporating a non-rising spindle operated via a T shaped (all models excluding 513042) or hand wheel operating member (model 513042 only) and EPDM seats. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
'DURACON®M90-44 WK3068'. Black coloured, injection moulded POM material. For use with water up to 85°C.
'PCBIT III HIGHBUILD'. Factory applied, black coloured bituminous coating. Apply as per manufacturer's instructions for use, reference 'PCC/ PC 820' dated 27.11.2023. Cure for 5 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Zhenxin Epoxy Powder Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's 'Preparation and Curing Conditions' instructions reference 'ZX-9-1', dated '2024/02/26'. Cure for 30 minutes@180°C. For use with water up to 85°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
KARUMEL EX4413-F103. Factory applied, fusion bonded, epoxy powder coating available in blue or red. Apply and cure in accordance with 'Application Guide KARUMEL EX4413-F103', issue 'KCSA-230201', dated February 2023, (curing as per Section 3.6). For use with water up to 85°C.
'SGPAM-CN-WB01'. Factory applied, blue coloured water based coating. Apply as per manufacturer's TDS 'PAMPIPE-TDC-WA04', version '4', dated '16/11/2022'. Cure for 30 minutes@50°C. For use with water up to 23°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CORROPOXY-FGE400'. Factory applied, red coloured, two-component epoxy coating. Mix and apply as per manufacturer's Application Procedures 'CPE/ FGE-400/Procd. /02', 'issue no - 03', dated '12.05.2022'. Cure for 30 minutes@45°C. For use with water up to 45°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'Welmortar-BFS'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14B', revision '01', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-SRP'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14C', revision '1', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Resicoat RS Redbrown & Blue'. ‘Resicoat RS 506530’ (blue coloured) was added to the approval in December 2024. Factory applied, two component, redbrown or blue coloured epoxy coatings. Mix in a ratio of 2:1 and apply as per product sheet 'revision no. 4' dated 'May 11, 2023'. Harden for 24 hours@23°C. For use with water up to 60°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Klubertop TP 38-901’. Site applied, (transparent) white coloured PTFE lubricant coating. Apply and cure as per Kluber Lubrication product information sheet ‘Prod. 099030, en-GB, Edition 12.05.2022’. For use with water up to 85°C.
'KORASILON® Paste hochviskos' & 'KORASILON® Paste M-S 2-200'. White coloured (translucent) lubricants. Apply as per manufacturer's Product Data Sheet '30.01.2023'. For use with water up to 85°C.
'Vydyne A 30 GF Black WR'. Black coloured, 30% glass fibre reinforced, injection moulded PA66 material. For use with water up to 85°C.
'BWRB1620200'. In July 2024 the following pipes were added to the approval: ‘BWRB1620100, BWRB2020200, BTRB2525100 & BTRB3230100. Triple layered, extruded pipes consisting of an off-white coloured PERT inner layer, aluminium middle layer and white coloured PERT outer layer. For use with water up to 85°C.
Page 50 of 113
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
