Range of in line regulating valves with brass bodies, EPDM `O` rings. The valves incorporate a non-rising spindle headwork for temperature regulation. Max working pressure: See models. max operating temperature: See models.
Range of in-line electrolytic scale reducers with copper bodies for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
In-line polyphosphate scale inhibitor. The product is supplied with a single check valve cartridge in the inlet connection, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Cold water use only.
Range of ultraviolet disinfection units consisting of a stainless-steel body and quartz sleeve. Maximum working pressure: 10.0 bar. Maximum operating temperature: 25.0°C.
'JSGL-SRC (U)'. Factory applied, grey coloured Sulphate resistant cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSGL-OPC (E)'. Factory applied, grey coloured Ordinary Portland cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSGL-OPC (U)'. Factory applied, grey coloured Ordinary Portland cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Miflex Type 103'. Dual layered, extruded PVC hoses comprising of a polyester reinforced black coloured inner layer and grey, red or blue outer layer. For use with water up to 60°C.
'ULTRAMID® D3EG12 AQUA BLACK 102'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'Diamant, Carat XL/XXL, Platin, Platin XL/XXL, Spring Water Shaft & Space-Saving Tank’ panels. White coloured (opaque), roto-moulded PE panels The approval includes panels manufactured in Germany (from September 2024 onwards) and France (from December 2024 onwards). For use with water up to 23°C.
'ME0940 'O' rings'. Black coloured, injection moulded EPDM rubber 'O' rings. Shore hardness between 40 & 90. Tested in-radii sizes between 1.0mm & 5.0mm. For use with water up to 85°C.
'EPDM 70: Blaco_Water/Food-EE70’. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70 A. Tested in-radius size 0.75mm. For use with water up to 85°C.
'EPDM B1-4771'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
Range of stop valves with plastic bodies. The valves incorporate a built-in solenoid valve which is operated by a switch located on the valve or by a remote control. The leak detector supplied with models SVSM66MRD & SVSM44MRD is not connected to any water pipe, is independent of the valve and is intended to be installed in the area at risk of leakage. It is intended to detect leakage and sends an electrical signal to close the valve. Please note that claims of leak detection have not been verified by WRAS For use with copper pipe (manufactured to BS EN1057), PEX pipe (manufactured to BS7291-3) and PB pipe (manufactured to BS7291 -2). Maximum working pressure 10.0 bar. Cold water use only.
Range of single-hole, multiple outlet, swivel, combination tap assemblies (brass bodies - various finishes) a quarter turn ceramic disc controlling the flow to the swivel arm with a dome type operating member and a ceramic cartridge with a single lever controlling the flow to the pull-out spray outlet incorporating a plastic aerator. The spray outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway 98°C, for mixed water pathway 65C and purified water pathway 85°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies. Incorporating a solenoid valve activated via an infra-red sensor. The inlets to the control box incorporate stainless steel strainers and the outlet incorporates a plastic aerator. Maximum working pressure: 8 Bar Maximum operating temperature: 65°C
Bottom entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies with a drain port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
‘Precolor’ range of one piece, pre-insulated cold water storage cisterns and covers for domestic water storage, supplied with a wholesome water kit. The cisterns walls are available in grey, blue, green, white, red and anthracite grey (external) colours and the cistern base is straw coloured. For cold water use only. From November 2024 the water contact layer of the cistern base and walls is available in grey or straw colours. The outer layer of the cistern base is available in blue, green, white, red and anthracite grey colours.
Range of aerators with plastic bodies and EPDM ‘O’-rings. Maximum operating temperature 65°C Open outlet use only
Page 455 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
