'BE50' & 'Bn BE50-100'. Natural (off-white), injection moulded polypropylene material. For use with water up to 85°C.
'1024 Titan Bladder'. Clear (translucent), extruded TPU bladder. Shore hardness 87. Tested in-radius size 0.48mm. For use with water up to 80°C.
'Pimtaş Plastik PVC-U Pipe'. Grey coloured, extruded PVC-U pipe. For use with water up to 50°C.
'+GF+ uPVC Pressure pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 50°C.
'E 71 65 003'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.5mm. For use with water up to 85°C.
'EP703904 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'EP703904 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'TRA-7073'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM70(E7-512K)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'LCKB70'. Black coloured, compression moulded EPDM material. Shore hardness 70A. Tested in-radius size 1.3mm. For use with water up to 85°C.
'FDJ-75'. Black coloured, injection moulded FKM rubber material. Shore hardness 76. Tested in-radius size 1.03mm. For use with water up to 85°C.
'NE7130 Grey 60'. Light grey coloured, injection moulded silicone rubber material. Shore hardness 60. Tested in-radius size 1.97mm. For use with water up to 85°C.
'Loctite 403'. Clear, liquid cyanoacrylate adhesive. Apply as per manufacturer's technical data sheet reference ‘2.6’, dated August 2012. Cure for 72 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘JET Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘P02415', updated 11/07/24 and this material is only approved for these conditions. For use with water up to 85°C.
'Datkafix DF-43'. Blue coloured pipe sealant. Apply as per manufacturer's TDS '01/02/2024 v1.1'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TruTite™ 313 Thread Lock'. Blue coloured pipe sealant. Apply as per manufacturer's TDS version '1.0 26/07/24'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CORE®'. Blue coloured pipe sealant. Apply as per manufacturer's instructions version '1', issue date '26/07/24'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ultra Tight Thread Sealing Cord'. White coloured (opaque) sealing cord. Apply as per manufacturer's TDS 'V1.0'. For use with water up to 85°C.
Range of wall mounted, two hole, single outlet (fixed) mains electric or battery controlled tap assemblies (chromium plated brass) incorporating approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection . The flow is controlled via a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The tap is supplied with spherical valves for both hot and cold inlets. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of deck mounted, Infra-red electronic basin mixers with mixing device and adjustable temperature limiter. The tap incorporates EPDM O-rings. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of wall mounted, single-hole, single outlet, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products incorporate a stainless steel braided PEX lined flexible hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Page 431 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
