'APE 55 N'. Black coloured, injection moulded EPDM rubber material. Shore hardness 55. Tested in-radius 1.1mm. For use with water up to 23°C.
‘TWK7534, TWK5810, TWK5811, TWK5812, TWK5813, TWK5814, TWK5815’. Black coloured, injection moulded EPDM materials. Shore hardness between 55A & 85A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'GM-EP01'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.15mm. For use with water up to 23°C.
'EPDM E282'. Black coloured, compression moulded EPDM sheet material. Shore hardness 80A. Tested in-radius size 1.0 For use with water up to 85°C.
'E7014F'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C. From April 2023, the material is for use with water up to 85°C.
'EPDM 70.503-00'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'51616 – E40, 51616 – E50, 51616 – E60, 51616 – E70 & 51616 – E80'. Black coloured, compression moulded EPDM materials. Shore hardness between 40 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'5594610'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘Sunaflex T 9635’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'A-KT 80-00'. Black coloured, extruded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.1mm. Between April 2023 and May 2025, the material was for use with water up to 23°C. Between June 2025 and April 2028, the material is for use with 85°C.
'A-KT 90-00'. Black coloured, extruded and rotocured EPDM rubber material. Shore hardness 90. Tested in-radius size 1.0mm. Between April 2023 and October 2024, the material is for use with water up to 23°C. From November 2024, the material is for use with water up to 85°C.
'EPNER-4665'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 50°C.
‘CRIEP50 & CRIEP80’. Black coloured, compression moulded EPDM rubber materials. Shore hardness 50 & 80 respectively. Tested in-radius size 1.0mm. For use with water up to 70°C.
Range of flow restrictors with natural/unpigmented plastic bodies and inserts (where applicable), and EPDM ‘O’-rings. The LFB-FDN15, BFDN15SH & LFB-FDN15SH models also incorporate a stainless-steel filter.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridges or 2-way ceramic disc diverter headworks with plastic bodies, EPDM ‘O’-rings and/or gaskets, for insertion into specifically dimensioned bores. The JA01AJ and AH01AJ models incorporate a thermostatic element. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridge headworks with plastic bodies and EPDM ‘O’-rings for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Thermostatic cartridges with plastic bodies, stainless steel mesh strainer and EPDM ‘O’ rings. For insertion into specifically dimensioned bores. Maximum operating pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of single hole, single outlet (swivel) combination tap assemblies, brass bodies with (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with an approved installation kit consisting of stainless-steel braided EPDM lined flexible hose assemblies with ½” BSP (F) captive nut end connections with 15mm compression single check valve assembly (suitable for backflow protection against Fluid Category 2) verified by test that also incorporates an isolation valve, intended for installation at each inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes). Incorporating quarter turn ceramic disc headworks with single lever, cross top, or dome type operating members. The spout outlets for models (F4184, F6182B & F9484) incorporate a plastic aerator and models (F6182C & F8118) are open outlet. The products are supplied with stainless-steel braided EPDM lined flexible hoses to headworks to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Three-hole, single outlet, (fixed), combination tap assembly, (brass body – various finishes). Incorporating quarter turn ceramic disc headworks with cross top operating members. The product is supplied with stainless-steel braided EPDM lined flexible hose assemblies to connect the headworks to the spout outlet and a lever type pop up waste. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Page 43 of 117
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
