'Edelpoxy FN TM 142'. Factory coloured, red coloured epoxy resin coating consisting of a base and hardener. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's IFU 'PCC/ PC 142', dated '10.07.2018'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VPC5015 Sky Blue FBE'. Factory applied, blue coloured fusion bonded, epoxy powder coating. Pre-heat the surface to be coated to 200°C for 5 minutes and dip in a fluidised bed of powder coating as per manufacturer's data sheet 'VPC5015, revision 5' dated '25 January 2023'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaguard CSF 585'. Factory applied, light blue coloured two component epoxy coating consisting of a base and hardener. Mix base & hardener in a volume ratio of 77.5:22.5 and apply as manufacturer's Product Data Sheet '7785', revised May 31, 2022. Cure for 15 days@21°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaline 523'. Factory applied, two-component, yellow coloured or red/brown coloured epoxy coatings. Mix and apply in accordance with Product Data Sheet ref. 7623 dated February 4, 2021. Cure for 3 days@23°C. The red-brown coloured coating is for use with water up to 60°C. Between June 2024 and March 2025, the yellow-coloured coating is for use with water up to 23°C. Between April 2025 and June 2029, the yellow-coloured coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SMS EPX-02 Solvent Free Epoxy Coating and Hardener'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix coating & hardener in a 3.5:1 volume ratio and apply as per manufacturer's painting instructions 'Document Code 30', 'Rev No 7', dated '01.09.2018'. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Luberpox-2K-DS-Lackfarbe IV17'. Factory applied, blue coloured, two-component epoxy coating. Mix coating and hardener in a weight ratio of 4:1 or volume ratio of 3:1 and apply as per manufacturer's TDS '01 – 11.06.2024'. Cure for 7 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Truform Cement OPC 43 Grade'. Factory applied, grey coloured cement. Mix cement:sand in a weight ratio of 2:1 and add 0.5 litres of water. Apply as per manufacturer's instructions 'TTPL/SOP/MCD/03', revision '00', dated 01.04.2018. Cure for 24 hours@27°C followed by 7 days@85°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Witcoat SF Epoxy Red Primer. Factory applied, red coloured, two-component epoxy primer. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's data sheet '15.09.2023 Rev No.: 00'. Cure for 7 days@30°C. For use with water up to 50°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix & cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SIGMACOVER 280 (Yellow/Green) + SIGMAGUARD CSF 650 (Green)'. Factory applied, light green coloured (once applied), epoxy primer & coating. Mix base and hardener of SIGMACOVER 280 in a 4:1 volume ratio and apply as per manufacturer's PDS '7417', dated 'May 23 2024'. Cure for 24 hours@20°C. Mix base and hardener of SIGMAGUARD CSF 650 in an 80:20 volume ratio and apply as per manufacturer's PDS '7443', dated 'July 26, 2022'. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic® M689 AE (formerly known MasterSeal® M689AE)'. Factory applied, two-component, light grey coloured (once applied), polyurea coating. Mix parts A & B in a volume ratio of 1:1 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Sl_M689_06_20/v9/07_23/v10/01_24/v11/03_24'. Cure for 7 days@25°C. For use with water up to 70°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI.Hygienic HI-Build Epoxy'. Factory applied, two- component, blue coloured epoxy coating. Mix base and hardener in a weight ratio of 100:15 and apply as per manufacturer's instructions 'LMIEP1403032', dated '22/06/2024'. Cure for 2 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikadur® ADH2200 (formerly known MasterBrace® ADH2200)'. Site applied, grey coloured (once applied), two component Epoxy bedding and mortar. Mix parts A and B in a weight ratio of 60:40 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Br_2200_12_94/v4/07_19/v5/05_20/v6/01_24/v7/03_24'. Cure for 21 days@25°C. For use with water up to 40°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FiberTie Pipe Factory and Accessories W.L.L.GRE composite pipe'. GRE pipe which consists of a beige/yellow coloured inner layer and pale green coloured outer layer, manufactured by helical winding. For use with water up to 50°C.
'Purolite PFC 100E'. Brown coloured ion exchange resin. For use with water up to 85°C.
'Purolite C104EPLUS'. Cream coloured ion exchange resin. For use with water up to 23°C.
'WACKER® AK 350'. Colourless, transparent lubricant. For use with water up to 60°C.
'Ultramid® D3EG12 Aqua BK102'. Black coloured, injection moulded polyamide material. For use with water 85°C.
'VESTAMID L1930 Material (Natural)'. Natural (appears beige in colour), injection moulded polyamide 12 material. For use with water up to 85°C.
'Paryls PPA A6200GLXX' (XX denotes the weight percentage of glass fibre between 30% to 50%). Black coloured, glass fibre reinforced polyamide materials manufactured by twin screw extrusion. For use with water up to 85°C.
'ULTRADUR® B4300 G6 FC AQUA WHITE 25262 & ULTRADUR® B4300 G6 FC AQUA BLACK 15142'. White coloured & black coloured, injection moulded PBT materials. For use with water up to 85°C.
Page 403 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
