Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. The valves operate via a non-rising spindle headwork with hand wheel, bevel gear, electric actuator & stem cap operator operating methods. Maximum working pressure 10.0 or 16.0 bar. Maximum operating temperature 100°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with brass bodies, for use with copper pipe (manufactured to EN1057). Incorporating a either a handwheel or lockshield operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies, EPDM coated wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy ductile iron bodies and a ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of stop valves with brass bodies (see models) with T-type operating members. The 15mm, 22mm and 28mm compression sizes are for use with copper pipe (manufactured to EN 1057). The 20mm and 25mm compression sizes are for use PE pipes (manufactured to EN 12201-2). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Series 116’ range of balancing valves (DZR Brass body). Some models can be supplied with a thermometer (see model). The outlet of the 116144, 116154, 116244 & 116254 models incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against fluid category 2). Compression connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of regulating balancing valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of bedpan washers and macerators with flow controlled by solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid cat 5). Maximum working pressure 6 Bar Maximum operating temperature 60°C
‘Caleffi Ecal’ electrolytic anti-scale device with a stainless-steel filter and magnet, comprising of an in-line DZR brass body and a plastic housing. Maximum working pressure 16.0 bar. Maximum operating temperature 40°C.
Range of floor standing or wall mounted water dispensers which dispenses ambient and/or chilled water. Flow is controlled via self-closing headwork and products have either tap with lever operating members, a tap with floor pedal (floor standing models only), a bubbler with push button or a bubbler with floor pedal (floor standing models only). Maximum working pressure 6.0 bar. Cold water use only.
‘SIKAFLOOR 150 & SIKALASTIC-836 DW’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of SIKAFLOOR 150 in a 100:50 weight ratio and apply as per manufacturer’s PDS ‘October 2023, Version 11.0’. Cure for 4 hours@25°C. Mix parts A & B of SIKALASTIC-836 DW in a 100:100 volume ratio and apply as per manufacturer’s PDS ‘July 2022, Version 04.0’. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EPACRETE EPAPOX 25 & EPAPROOF FPCS WFC’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of EPACRETE EPAPOX 25 in a 100:50 weight ratio and apply as per manufacturers TDS 01.140317. Cure for 4 hours@25°C. Mix parts A & B of EPAPROOF FPCS WFC in a 100:100 volume ratio and apply as per manufacturers TDS rev 01-2023. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AFIL BLUE Tank Panel'. Beige coloured GRP tank panel manufactured by continuous winding. For use with water up to 60°C.
'AFIL BLUE Pipe'. Beige coloured GRP pipe manufactured by continuous winding. For use with water up to 60°C.
'Versilon™ C-544-A I.B'. Triple layered, extruded tube consisting of a transparent (clear) polyurethane inner layer, white coloured polyester middle layer & transparent (clear) polyurethane outer layer. For use with water up to 65°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Grivory HT1V-3 FWA natural and black 9225. Grivory HT1V-4 FWA natural and black 9225. Grivory HT1V-4 FWA grey 9489. Grivory HT1V-4 FWA grey-blue 4637. Grivory HT1V-5 FWA natural and black 9225. Grivory HT1V-5 FWA grey L1366.3 & Grivory HT1V-5 FWA grey 9616. Grivory HT1V-5 FWA grey L16760.2. Grivory HT1V-6 FWA natural and black 9225. For use with water up to 85°C.
'RADILON® DT RV300RKC2 106 NT to RADILON® DT RV500RKC2 106 NT and RADILON® DT RV300RKC2 306 BK to RADILON® DT RV500RKC2 306 BK'. Natural (appears off-white in colour) or black, injection moulded glass fibre filled PA6.12 materials. For use with water up to 85°C.
'Union Pipes Industry – K.S.A. HDPE Pipe' (made using BorSafe™ HE3490-LS, Hostalen CRP 100 Black, SABIC® HDPE P6006AD or TASNEE PE 100 black). Black coloured (with blue external stripes), extruded HDPE pipes. For use with water up to 60°C.
Page 398 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
