Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of inlet control groups with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve set to 6bar. The outlet incorporates a single check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2. Pressure reducing range 1 bar to 6 bar Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of double regulating valves available with bronze bodies. Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of water conditioners with stainless steel bodies. Maximum working pressure 10 Bar. Maximum operating temperature 85°C.
'TENAC-C 4590'. White (translucent) coloured, injection moulded acetal material. For use with water up to 85°C.
'Ak99,5 - 99,5% Alumina Ceramic'. Ivory coloured, compression moulded and fired Ceramic material. For use with water up to 85°C.
'ZHR‐SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2025.8.27'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Ecocoat FBE Green Powder PFC/6018 (RAL 6018)& Ecocoat FBE Red Oxide Powder PFC/3000-Red Oxide'. Factory applied, green or red coloured epoxy coatings. Apply as per manufacturer’s Product Data Sheet revised ‘1st Jan, 2024’. Cure for 3 minutes at a metal temperature of 230°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Eurokote® 48-20 Brun Rouge’. Factory applied, red coloured, two-part epoxy coating. Mix resin and hardener in a 2.13:1 mass ratio and apply as manufacturer's TDS dated '10/12/2024'. Cure for 24 hours@20°C. For use with water up to 23°C.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'G. Beslux Bessil EH-3'. White coloured silicone grease. For use with water up to 85°C.
Tecomid NA40 GR25 NL HS QF (white coloured) and Tecomid NG40 GR30 BK250 HS QW, Tecomid NA40 GR30 BK005 HY QH & Tecomid NA40 GR30 BK250 HY QW (black coloured). Injection moulded PA materials. Tecomid NA40 GR25 NL HS QF (white coloured) & Tecomid NG40 GR30 BK250 HS QW (black coloured) are suitable for use with water up to 85°C. Tecomid NA40 GR30 BK005 HY QH (black coloured) & Tecomid NA40 GR30 BK250 HY QW (black coloured) are suitable for use with water up to 23°C.
'HEP PB Pipe'. Off-white coloured, extruded Polybutylene-1 pipe. For use with water up to 85°C.
'HEP PB Fittings'. Off-white coloured, injection moulded Polybutylene-1 fittings. For use with water up to 85°C.
'Elysee HDPE PE 80 Blue Pipe'. Extruded, single layered (blue coloured) or dual layered (black coloured inner layer & blue coloured outer layer) HDPE pipes. For use with water up to 23°C.
'Flomasta Blue PE 80 Pipe'. Extruded, single layered (blue coloured) or dual layered (black coloured inner layer & blue coloured outer layer) HDPE pipes. For use with water up to 23°C.
'Hepworth Qatar PPR 125 Pipe'. Green coloured (opaque), extruded PPR pipe. For use with water up to 85°C.
'SABIC® PP 48M10'. White coloured, injection moulded polypropylene material. For use with water up to 85°C.
'SABIC® PP 56M10'. White coloured, injection moulded polypropylene material. For use with water up to 85°C.
Page 383 of 393
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
