‘SIGMAPRIME 200 K Grey’ for use with ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. ‘SIGMAPRIME 200 K Grey’ (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio and applied as PDS ‘7416’, dated February 25, 2021. Cure for 24 hours@23°C. ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’ is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio and applied as PDS ‘7785’, dated August 19, 2022. Cure for 12 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KAJ1207'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions 'file no. I01-KAJ1207' dated '2019.1.14'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KORASILON® Paste hochviskos' & 'KORASILON® Paste M-S 2-200'. White coloured (translucent) lubricants. Apply as per manufacturer's Product Data Sheet '30.01.2023'. For use with water up to 85°C.
'BWRB1620200'. In July 2024 the following pipes were added to the approval: ‘BWRB1620100, BWRB2020200, BTRB2525100 & BTRB3230100. Triple layered, extruded pipes consisting of an off-white coloured PERT inner layer, aluminium middle layer and white coloured PERT outer layer. For use with water up to 85°C.
‘4TECH 9S20000 W-A-ABK 01 0A QF, 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK’. Black coloured, injection moulded PPO & PPO/HIPS materials. 4TECH 9S20000 W-A-ABK 01 0A QF is an unfilled PPO material suitable for use with water up to 23°C. 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK are filled PPO/HIPS materials suitable for use with water up to 85°C.
'Bush (25122200)'. Dark grey coloured, extruded NEP-25%carbon/PTFE component. For use with water up to 85°C.
'CH200'. Brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'version 24/05/2018'. Cure for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'kSil GP200, kSil GP250, kSil GP350, kSil GP400, kSil GP450 & kSil GP530'. Pale yellow/white coloured, extruded silicone rubber cellular sponge materials. Shore hardness between 37 & 70. Tested in-radii sizes between 1.53mm & 1.76mm. For use with water up to 85°C.
'122102001 Valve Body'. Black coloured, injection moulded PVC-U valve body. For use with water up to 23°C.
Range of deck mounted taps for cold or premixed water with stainless steel bodies. Flow is controlled by a solenoid valve activated via an infra-red sensor, and the spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies in (chrome plated brass bodies). Flow is controlled with a solenoid valve activated via an infra-red sensor. The temperature is controlled via a single lever operating member on the body. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of spring loaded resilient trim check valve cartridges with a plastic body and EPDM ‘O’-rings. For insertion into specifically dimensioned bores Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Assisted bath incorporating a thermostatic mixing valve to control both the flow and temperature to either a spout outlet or shower handset. The discharge from the bath spout and shower handset in via a type AUK 3 airgap, verified by measurement, suitable for Fluid Category 5 backflow protection. The bath has adjustable height and tilt functions. Maximum working pressure: 6 Bar Maximum operating temperature: 45 °C
Range of aerators with plastic bodies and EPDM ‘O’-rings. Open outlet use only. Maximum operating temperature 65ºC.
Range of single hole, single outlet (fixed) combination taps assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure: See models. Maximum operating temperature 60.0°C
Range of deck mounted, single-holed, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Models (TVW104101110xx, TVW103004000xx, TVW125001000xx) are supplied with lever operated pop-up wastes (not verified by test). Models (TVW103005000xx, TVW104105110xx & TVW125002000xx) are supplied with click type pop-up wastes (verified by test). Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of deck mounted, single-holed, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Models (TVW105002000xx, TVW105003000xx, TVW105101110xx & TVW105141110xx) are supplied with lever operated pop-up wastes (not verified by test) Model TVW105105110xx) is supplied with a click type pop-up waste (verified by test). Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted spout outlets (brass bodies – various finishes) incorporating NBR O-rings and plastic aerators. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C
Page 37 of 56
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
