Directory Search Results

Print List

#250604718

Qmpress Instaboil Range of under counter electric instantaneous water heaters with stainless steel tank and heating element. Open outlet use only. Maximum operating temperature 98°C.

Section:
1365 Heaters
Section Subtitle:
Electric instantaneous, open outlet, mains fed.
WRAS Approval Number:
250604718
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP (M).
Marking:
QMPRESS logo printed on front panel. logo; Pressure, Capacity, Model No, WRAS and product info on data label.
Installation Requirements:
R001
Expiry date:
30/06/2030
Model:
Qmpress Instaboil 4in1 Boiler Water Heater Tanks.

Approval Holder:
QMPRESS LTD
Company Name
QMPRESS LTD
Address
Qmpress Ltd Cools, Headford, Killarney
Country
Ireland

View All Listings by this Company

Print This Approval


#250602716

Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. Some models, please refer to model below, incorporate only a primary circuit. Maximum working pressures: Primary circuit: 2.5 bar, Secondary circuit 10.0 bar. Maximum operating temperature both circuits: 60°C.

Section:
1465 Heaters
Section Subtitle:
Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:
250602716
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Marking:
Warmhaus on front panel. Warmhaus, product name and operating info on label on side panel
Installation Requirements:
R001 R140 R360
Expiry date:
30/06/2030
Model:
Following models are ¾” BSP M inlet/outlet primary circuit, ½” BSP M inlet/outlet secondary circuit. KM0725250101005901 EWA 2525C 25KW KM0725300101005901 EWA 2530 C 30 KW KM0725310303008701 MINERWA 25/31 COMBI BOILER IE (BLACK) KM0725300201008901 ENERWA PLUS 2530 C - UK KM0325300201001301 ENERWA PLUS 2530 C - UK + FLUE KIT KM0730350201008901 ENERWA PLUS 3035 C - UK KM0330350201001301 ENERWA PLUS 3035 C + F.KIT - DHW 35 - UK KM0735400201008901 ENERWA PLUS 3540 C - UK KM0335400201001301 ENERWA PLUS 3540 C - UK KOMBI KM0742400201001301 ENERWA PLUS 4240 C 40 KW - UK KM0745430201001301 ENERWA PLUS 4543 C 43 KW - UK KM0725310303009801 EXP.MINERWA 25 SYSTEM BOLER (BLACK) KM1220240101012201 GLOWA 2024 KM1224260101012201 GLOWA 2426 KM1228300101012201 GLOWA 2830 KM1233350101012201 GLOWA 3335 KM1220240101012401 GLOWA SMART 20/24 20KW KM1224260101012401 GLOWA SMART 24/26 24KW KM1228300101012401 GLOWA SMART 28/30 28KW KM1233350101012401 GLOWA SMART 33/35 33KW Following models are ¾” BSP M inlet/outlet and are primary circuit only KM1024000201005501 EXP.ENERWA PLUS H.O 2500H KM1024000201010201 EXP. WARMHAUS ENERWA PLUS H.O 2500H - UK KM1028000201005501 EXP.WARMHAUS ENERWA PLUS H.O 3000H KM1028000201010201 EXP.WARMHAUS ENERWA PLUS H.O 3000H - UK KM1033000201005501 EXP.WARMHAUS ENERWA PLUS H.O 3500H KM1033000201010201 EXP.WARMHAUS ENERWA PLUS H.O 3500H - UK KM1133000201005501 EXP.WARMHAUS ENERWA PLUS H.O 3500H+F.KIT KM1133000201006201 EXP.WARMHAUS ENERWAPLUS HO 3500H-D+F.KIT KM1142000201005501 ENERWA PLUS H.O 4200H KM1145000201005501 ENERWA PLUS H.O 4500H KM1220000101012301 GLOWA 20 H.O. KM1224000101012301 GLOWA 24 H.O. KM1228000101012301 GLOWA 28 H.O. KM1233000101012301 GLOWA 33 H.O.

Manufacturer:
Warmhaus Isitma VE Sogutma Sistemleri Sanayi Ticaret A.S.
Company Name
Warmhaus Isitma VE Sogutma Sistemleri Sanayi Ticaret A.S.
Address
Nilufer Organise Sanayi Bolgesi Selvi Cad No:3 Nilufer Bursa Turkey
Phone
+90-224-2959400

View All Listings by this Company

Print This Approval


#250602045

Range of water meters with brass and plastic bodies and plastic turbines. The inlet incorporates a plastic filter Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C

Section:
1505 Water Meters
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
¾” to 2 ½” BSP M (G models) DN 50 flanged (FL Models)
Marking:
Zenner logo, Model, ZR, CE, date of manufacture (YYYY) and other information on faceplate. Flow arrow and date of manufacture (YYYY) on body.
Installation Requirements:
R001 R008
Expiry date:
30/06/2030
Model:
MTKD 2,5-165-G ¾ B (½) MTKD 4-190-G 1 B (¾) MTKD 6,3-260-G 1 ¼ B (1) MTKD 10-260-G 1 ¼ B (1) MTKD 10-260-G 1 ½ B (5/4) MTKD 16-300-G 2 B (6/4) MTKD 25-270-G 2 ½ B (2) MTKD 25-300- G 2 ½ B (2) MTKD 25-270-FL MTKD 25-300-FL MTKD-L 2,5-165-G ¾ B (½) MTKD-L 4-190-G 1 B (¾)

Manufacturer:
Zenner International Gmbh & Co. KG
Company Name
Zenner International Gmbh & Co. KG
Address
Heinrich‐Barth‐Str. 29, 66115 Saarbrücken, Germany
Country
Germany

View All Listings by this Company

Print This Approval


#250602705

Range of flow meters with plastic bodies. Maximum working pressure 8.0 bar Maximum operating temperature 40°C.

Section:
1530 Miscellaneous Fittings
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
3/8” BSP (F) x 3/8” BSP (M)
Marking:
BWT Logo on LCD display. Digmesa and flow arrow on body.
Installation Requirements:
R001
Expiry date:
30/06/2030
Model:
812486 (930-0074) Aquameter 3/8” with Relais. 812185 (938-A930/LE5117) Aquameter 3/8” with LCD Display. 812495 (938-A70/LE5113) Aquameter HF 3/8” with LCD Display.

Approval Holder:
BWT Holding GmbH
Company Name
BWT Holding GmbH
Address
Walter-Simmer-Straße 4 Mondsee
Postcode
5310
Country
Austria
Phone
+436648172152
General Email
andreas.stiegler@aidu.solutions

View All Listings by this Company

Print This Approval


#250602715

Range of bidet spray kits, wall outlet and brackets with brass bodies (various finishes), bidet spray kits consist of a wall outlet bracket, double interlocking flexible hose and a handset with self-closing trigger mechanism. Maximum working pressure 5 Bar. Maximum operating temperature 60°C.

Section:
1530 Miscellaneous Fittings
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP M
Marking:
Bidet Spray Kits: Samuel Heath logo on handset. Samuel Heath logo, WRAS and date on manufacture (YYYY) on conical nut. Samuel Heath logo on wall elbow body. Wall Outlet and Bracket: Samuel Heath logo on body
Installation Requirements:
R001 R090 R415
Expiry date:
30/06/2030
Model:
Bidet Spray Kits V159-SPR-XX V266-SPR-XX V666-SPR-XX V766F-SPR-XX V766K-SPR-XX T166-SPR-XX Wall Outlet and Brackets V159-XX V266-XX V666-XX V766F-XX V766K-XX T166-XX Where the product code suffix ‘XX’ denotes the surface finish. It will always be 2 or 3 digits, which can be any combination of numbers and/or letters. CP = Chrome plate, PN = Polished nickel, SSF = Stainless steel finish, NL = Non-lacquered, BG = Brushed gold, BGG = Brushed gold gloss lacquered, BGM = Brushed gold matt lacquered, CTB = City bronze, CNB = Country bronze, AG = Antique gold, MBC = Matt black chrome, SSB = Stainless steel finish, URB = Urban brass & URM = Urban brass matt ANT = Anthracite, OBM = Old Brass Matt, AMR = Amber Brass, ABG = Antique Brass Gloss, ABM = Antique Brass Matt

Manufacturer:
Samuel Heath & Sons Plc
Company Name
Samuel Heath & Sons Plc
Address
100 Leopold Street Birmingham
Postcode
B12 0UJ
Country
United Kingdom
Phone
+44 (0) 1217 662 200

View All Listings by this Company

Print This Approval


#241002724

Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
241002724
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Note:
The discharge from the drain plug must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717.
Size:
CWMA3 & CWMA5 : 1” BSP (F) inlet x 1” BSP (F) outlet. CWMA7 : 1¼” BSP (F) inlet x 1” BSP (F) outlet. CWMA9 : 1½” BSP (F) inlet x 1¼” BSP (F) outlet. CWMA18 : 2” BSP (F) inlet x 1½” BSP (F) outlet.
Marking:
Winflo logo, model code and product technical information on data-plate.
Installation Requirements:
R001 R415
Expiry date:
31/10/2029
Model:
CMWA range model code: CMWAXX-Y(T) CMWA = Pump type. XX = Nominal flow rate m/3 per hour (3, 5, 7, 9 or 18). Y = Number of impellers. T = 3 phase or (blank) = single phase. CMWA3-2, CMWA3-3, CMWA3-4, CMWA3-5, CMWA3-6 & CMWA3-7. CMWA5-2, CMWA5-3, CMWA5-4, CMWA5-5, CMWA5-6 & CMWA5-7. CMWA7-2, CMWA7-3, CMWA7-4, CMWA7-5 & CMWA7-6. CMWA9-2, CMWA9-3, CMWA9-4 & CMWA9-5. CMWA3-2T, CMWA3-3T, CMWA3-4T, CMWA3-5T, CMWA3-6T & CMWA3-7T. CMWA5-2T, CMWA5-3T, CMWA5-4T, CMWA5-5T, CMWA5-6T & CMWA5-7T. CMWA7-2T, CMWA7-3T, CMWA7-4T, CMWA7-5T, CMWA7-6T & CMWA7-7T. CMWA9-2T, CMWA9-3T, CMWA9-4T & CMWA9-5T. CMWA18-2T, CMWA18-3T & CMWA18-4T.

Approval Holder:
Eautechnik GmbH
Company Name
Eautechnik GmbH
Country
Germany

View All Listings by this Company

Print This Approval


#250602011

Range of overhead shower outlets (ABS plastic - various finishes), incorporating a stainless-steel strainer. Open outlet use only Maximum operating temperature 60.0°C.

Section:
1650 Shower Outlets
Section Subtitle:
Shower head(s) and/or shower handset(s).
WRAS Approval Number:
250602011
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
1/2” BSP (F)
Marking:
Villeroy & Boch on side of body
Installation Requirements:
R001 R040
Expiry date:
30/06/2030
Model:
A957328xx Where xx denotes the finish, and can be replaced with either of the following: AA – Chrome XG – Silk Black

Approval Holder:
Villeroy & Boch AG
Company Name
Villeroy & Boch AG
Address
Saaruferstraße 1-3 Mettlach
Postcode
66693
Country
Germany
Phone
+49 151 16775778
General Email
Finkler.Marc@villeroy-boch.com

View All Listings by this Company

Print This Approval


#250602028

Range of wall or ceiling mounted shower outlets with chromium plated bodies (or black body for 22123KF0) consisting of showers arms and shower head for installation with specific rough-in sets. Shower head bodies incorporate approved single check valve cartridges, however, the complete assemblies have not been tested to demonstrate it provides backflow protection. The 26.484 model rough-in set incorporates a plastic flow regulator on the inlet. Maximum working pressure: Open Outlet. Maximum operating temperature: 60°C.

Section:
1650 Shower Outlets
Section Subtitle:
Shower head(s) and/or shower handset(s).
WRAS Approval Number:
250602028
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Note:
Any flow rates claimed by the manufacturer have not been verified
Size:
½” BSP (F).
Marking:
Showerheads: Grohe on face. Concealed bodies: Grohe, Date of manufacture (YYMMDD), Made in Germany on adhesive label inside plastic shell, Grohe, DR and Flow arrows on brass body.
Installation Requirements:
R001 R040
Expiry date:
30/06/2030
Model:
Grohe ‘RSH’ Cosmopolitan 310’ headshower sets 400mm: 26.475.xxx & 26.479.xxx. Grohe ‘RSH’ Smart Active 310’ headshower sets 400mm: 22123KF0 Concealed bodies (rough-in sets): 26.483 & 26.484 Where xxx denotes finish, can be replaced by: 000 – Chrome DC0 – Supersteel DA0 – Warm sunset AL0 – Brushed hard graphite A00 – hard graphit BE0 – polished nickel DL0 – brushed warm sunset EN0 – brushed nickel GN0 – brushed cool sunrise GL0 – cool sunrise LS0 – moon white A00 – hard graphite

Manufacturer:
Grohe AG
Company Name
Grohe AG
Address
Industriepark Edelburg Hemer
Postcode
58675
Country
Germany
Phone
02372 930

View All Listings by this Company

Print This Approval


#250608015

Range of overhead shower outlets with stainless steel bodies (various finishes). The inlet incorporates a stainless-steel filter and a plastic flow regulator. Maximum working temperature 45°C. Open outlet use only.

Section:
1650 Shower Outlets
Section Subtitle:
Shower head(s) and/or shower handset(s).
WRAS Approval Number:
250608015
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP (F).
Marking:
Dolphin Solutions Ltd logo on the body.
Installation Requirements:
R001 R040
Expiry date:
30/06/2030
Model:
DB3001.a.bbb Dolphin blue round shower head DB3002.a.bbb Dolphin blue square shower head Where: The suffix .a in the above codes will be a number 1 - 9 to denote the finish: .1 to denote brushed/satin polished. .2 to denote mirror polished. .3 to denote brushed/satin polished with PVD coating. .4 to denote mirror polished with PVD coating. .5 to denote powder coated. .6 - 9 to denote other material and finish options. The suffix .bbb in the above code indicates the colour of the PVD or powder coat. It can be either two or three digits from 01-999.

Approval Holder:
Dolphin Solutions Limited
Company Name
Dolphin Solutions Limited
Address
Southpoint Compass Park Bodiam East Sussex
Postcode
TN32 5BS
Country
United Kingdom

View All Listings by this Company

Print This Approval


#250604014

Range of pillar taps ( brass body - various finishes, see), CR20 and CR20/501 incorporate a non-rising spindle headworks with a dome type operating member. GE02 and GE02/201 incorporating quarter turn ceramic discs headworks with a lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
1800 Taps
Section Subtitle:
Pillar tap(s).
WRAS Approval Number:
250604014
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” BSP (M).
Marking:
DEVA & DTC 59 on body.
Installation Requirements:
R001 R006
Expiry date:
30/06/2030
Model:
CR20, CR20/501 (GOLD), GE02, GE02/501 (GOLD).

Approval Holder:
Methven UK Limited
Company Name
Methven UK Limited
Address
Methven Experience Centre 3-3A Stone Cross Court Yew Tree Way Golborne Warrington
Postcode
WA3 3JE
Country
United Kingdom
Phone
0800 195 1602
General Email
raluca.olariu@uk.methven.com

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 357 of 446

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.