Range of EBCO stop valves with gunmetal bodies with a various end connections. Maximum working pressure 16 bar. Cold water use only.
Activflo Lite range of water conditioners with copper bodies. Models with compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of inline water conditioners with zinc/copper alloy bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of UV disinfection units, for above ground use only. Maximum operating pressure 10.0 bar. Cold water use only.
“CN Pressure vessel” range incorporating a HDPE liner. The products have a separate outer layer (with black, blue, grey or natural finishes). The CN Pressure vessel 24x72” D-4 model has a top and bottom opening. Maximum operating pressure 10.5 bar. Cold water use only.
'ABS-040 Black'. Black coloured, injection moulded ABS material. For use with water up to 85°C.
'WHC1850'. White coloured, dry pressed ceramic disc. For use with water up to 85°C.
'Relithane 151. Factory applied, brown coloured, two-component Polyurethane coating. Mix base and hardener in a 2.5:1 ratio and apply as per manufacturer's 'Standard Operating Procedure & Guidelines, Revision 2, 157/2022' dated 12th October 2022. Cure for 40 seconds@35°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL 8423'. Factory applied, dark blue coloured enamel coating. Apply as per manufacturer's TDS '08423', version '02-2024' and cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APCOSHIELD FBVL EX400G – RAL 5005 Blue & RAL 5017 Blue'. Factory applied, blue coloured epoxy coatings. Apply as per manufacturer’s datasheet ‘PDS/APPPG/V01/01-2024’. Post-cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APCOSHIELD FBPC EX405SG INTER GREEN'. Factory applied, green coloured epoxy coating. Apply as per manufacturer's data sheet 'PDS/APPPG/V02/01-2024'. Post-cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 HT Red'. Factory applied, red coloured (once mixed), two-component epoxy coating. Mix base and hardener in a volume ratio of 3:1 and apply as per manufacturer's instructions 'Chembur R&D/PI/23/02' dated 28/12/2023. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotun Marathon IQ2'. Factory applied, two-component, grey coloured epoxy coating. Mix parts A:B in a ratio of 3:1 parts and apply as per 'Jotun Marathon IQ2' Technical Data Sheet dated '16 April 2021'. Cure for 7 days@23°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'G52-06 Quick-drying type Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured polyethylene coating. Apply as per manufacturer's data sheet 'XYJSMS002', dated January 10th, 2023. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 200 K Grey’ for use with ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. ‘SIGMAPRIME 200 K Grey’ (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio and applied as PDS ‘7416’, dated February 25, 2021. Cure for 24 hours@23°C. ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’ is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio and applied as PDS ‘7785’, dated August 19, 2022. Cure for 12 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI Hygienic CML'. Factory applied, grey coloured cement mortar. Mix cement mortar:sand:water in a weight ratio of 36:46:18 and apply as per manufacturer's instructions 'LMICMA012624', dated '1/26/2024'. Cure for 20 hours@40°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Alsen FBE Blue Powder Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's Product Data Sheet 'AIPL 1212/1', dated '07/06/2023'. Cure for 2.5 hours:235°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DIMERSIL 10`. Green coloured, compressed synthetic fibre sheet material manufactured by calendaring. For use with water up to 23°C. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'SUS-GRP01'. White coloured GRP panel manufactured by hot press moulding. For use with water up to 65°C.
'Crystic Gelcoat 65PA Gel Coat' for use with 'Crystic 125PA GRP resin'. GRP resin, manufactured by hand lamination, for use with white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 352 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
