Inlet control group with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve (6.0 Bar). The inlet incorporates a stainless-steel strainer, and the outlet incorporates an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The product is for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C. Outlet pressure range of the pressure reducing valve is 1.0 to 4.0 bar.
Range of in line regulating valves with brass bodies, EPDM `O` rings. The valves incorporate a non-rising spindle headwork for temperature regulation. Max working pressure: See models. max operating temperature: See models.
In-line electrolytic scale reducer with chromium plated copper body for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of in-line electrolytic scale reducers with copper bodies for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Range of ultraviolet disinfection units consisting of a stainless-steel body and quartz sleeve. Maximum working pressure: 10.0 bar. Maximum operating temperature: 25.0°C.
Oasis Kalix range of water dispensers which dispenses hot and cold water. The flow is controlled via a solenoid valve and the products are activated via a push button or infrared sensor. The products incorporate a pressure relief valve with a plastic body which is rated at 5.0 bar. Maximum working pressure 3.0 bar Please refer to model for maximum operating temperature.
Range of commercial and domestic ion exchange water softeners (salt regenerated). Operation is by an electronically controlled ion exchange resin filled plastic pressure vessel with integral salt cabinet (domestic models) or separate brine tank (commercial models). Maximum working pressure 8.0 bar. Cold water use only.
'SP01BL'. Black coloured, injection moulded POM material. For use with water up to 85°C.
'KOCETAL® K100BK & KOCETAL® K300BK'. 'KOCETAL® K500BK’ was added to the approval in June 2025. Black coloured, injection moulded POM materials. For use with water up to 23°C.
‘KOCETAL® K100HSP (white coloured) & KOCETAL® K100HSP BK (black coloured)’. Injection moulded POM materials. For use with water up to 23°C.
‘KOCETAL® WR301 (white coloured) & KOCETAL® WR301 BK (black coloured)’. Injection moulded POM materials. For use with water up to 23°C.
'M-106'. Grey coloured, compression moulded mechanical carbon graphite cylindrical component. For use with water up to 85°C.
'M-133'. Grey coloured, compression moulded mechanical carbon graphite cylindrical component. For use with water up to 85°C.
'DL-001'. White coloured, compression moulded ceramic washer. For use with water up to 85°C.
'J1200 (RBSIC) & J1300 (SSIC)'. Grey coloured, compression moulded and sintered, Silicon carbide mechanical sealing rings. For use with water up to 85°C.
'H/E16018'. Factory applied, dark blue coloured electrostatic enamel coating. Apply as per manufacturer's TDS '00', dated '30.08.2017' and cure for 4.5 minutes at a peek temperature of 850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOROGUARD 20 RED & GREY'. Factory applied, two-component epoxy coatings available in red and grey. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's TDS dated 'Jan 2024'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APLICAPROOF PUA P'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'Rev - 06/2024'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APLICAPROOF PU W'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS 'Rev -06/2024'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hempadur 35560 Cream Coating with Hempadur 15590 Red Primer'. Factory applied, cream coloured, two-component epoxy coating for use with epoxy primer. ‘Hempadur 15590 Red Primer’ is a two-component primer to be mixed in a 15:4 volume ratio and applied as per manufacturers PDS dated ‘October 2024’. Cure for 16 hours@20°C. 'Hempadur 35560 Cream’ is a two-component coating to be mixed in a 6.8:2 volume ratio and applied as per manufacturers PDS dated ‘May 2024’. Cure for 7 days@20°C. For use with water up to 35°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 345 of 522
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
