'DX101, DX201, DX202 & DX203 Rings'. Dark grey coloured, compression moulded silicon carbide ring components. For use with water up to 85°C.
'HEMPADUR 85671 System'. Factory applied epoxy coating system comprising of a pink base coat (50900), light green middle coat (42070), and pink top coat (50900 - water contact). Each coat comprises of a base and curing agent to be mixed in a 8.8:1.2 volume ratio before applying in accordance with manufacturer's PDS dated January 2023. Cure each coat for 7 days@20°C and then 20 hours@40°C. For use with water up to 30°C.
'VPC5009 Potable FBE'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate at 200°C and then apply by dipping in a fluidised bed as per manufacturer's instructions dated 10th January 2019. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Pentens SPU-1000 Pure Polyurea Waterproofing Spray Coating (with Pentens E-500SE Primer and Pentens E- 501S Sealer)’. Factory applied, dark yellow coloured (once applied) polyurea primer, sealer & top coat. Mix primer in a 1:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix sealer in a 2:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix topcoat in a 1.125:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 72 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eucoflex Caliente'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet 'TX40T815', dated 'August 2023'. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Euclid Chemical Toxement. The authorization, training and certification of the local applicators are the responsibility of Euclid Chemical Toxement and not the responsibility of WRAS.
'TPU 2053, TPU 2054, TPU 2055, TPU 2056, TPU 2057 & TPU 2058'. Five layered, membrane systems manufactured by calendaring. The membranes consist of: 1.) a transparent polyurethane inner layer (in contact with the water), 2.) a tie layer, 3.) a reinforcing layer (PES or PA), 4.) a tie layer & 5.) a blue or beige coloured polyurethane outer layer (not in contact with the water). For use with water up to 23°C.
'DISTITRON® VE 100 ST'. Beige coloured, glass fibre reinforced Vinyl Ester Resin manufactured by hand lay-up. For use with water up to 23°C.
'DISTITRON® VE 100 STD'. Beige coloured, glass fibre reinforced Vinyl Ester Resin manufactured by hand lay-up. For use with water up to 23°C.
'15.0903.01 & 15.0902.01'. Dark grey coloured, ferrite anisotropic magnets (commonly known as ceramic magnets). For use with water up to 85°C.
‘Zytel® FG70G30HSR2 BK309’. Black coloured, injection moulded polyamide material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'Smart Joint Pipe'. Black coloured (with blue stripes), extruded HDPE pipe. For use with water up to 60°C.
'GS100ElPLAST'. Black coloured, extruded high density polyethylene pipe. For use with water up to 23°C.
'GS100ELPLAST'. Blue coloured, extruded high density polyethylene pipe. For use with water up to 23°C.
'ecoFIT PE 100 Pipe'. Black coloured, extruded PE pipe. For use with water up to 23°C.
'E7518'. Black coloured, injection moulded EPDM C-seals. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP90/4 BLK Seals and 'O' rings'. Black coloured, injection moulded EPDM seals and 'O' rings. Shore hardness 90. The seals have a tested in-radius size of 1.7mm. The 'O' rings have a tested in-radius size of 1.2mm. For use with water up to 85°C.
'EUW-70'. Black coloured, injection moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 60°C.
‘SMS-8000-Premium’. Black coloured, compression moulded EPDM material. Shore hardness 80 respectively. Tested in-radius size 1.0mm. For use with water up to 23°C.
'NPEPDM-80'. Shore hardness 80. 'NPEPDM-50' was added to the approval in December 2023. Shore hardness 50. Black coloured, compression moulded, EPDM materials. Tested in-radius size 1.0mm. For use with water up to 70°C.
'01/E90FKM Gaskets & 'O' rings'. Black coloured, injection moulded FKM gaskets & 'O' rings. Shore hardness 90. The gaskets have an in-radius size of 1.1mm and the 'O' rings have an in-radius size of 1.0mm. For use with water up to 85°C.
Page 329 of 566
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
