Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with ductile iron bodies, wedge and bonnet (blue epoxy powder coated) and EPDM `O` rings and gaskets. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure: 16.0 Bar Maximum operating temperature: 60°C
Range of gate valves with brass bodies, brass wedges and PTFE seals. The valves operate via a non-rising spindle and are supplied with either no operating member or a hand wheel (see models) Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of balancing valves with a bronze body, brass disc face and PTFE seat. The product incorporates two test points. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of inline water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
'PolyQuick® P-500 PW'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 05-2025'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SOLID-01'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35 and apply as per manufacturer's User Instructions 'SOLID-196', 'Vision: A-2', dated '2019-8-28'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PA6059 Pure Polyester Powder Coating'. Factory applied, blue coloured polyester coating. Apply as per manufacturer's instructions 'file no. FP180515 version 2' dated May 25, 2018. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOD-E-2024/1'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions 'T264', revision '00', dated '16.07.2024'. Cure for 25 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Evercrete Vetrofluid'. Site applied, colourless, cement waterproofing liquid. Apply two coats as per manufacturer's instructions dated '01 JULY 2024'. Cure Coat 1 for 4hrs 40mins@21ºC and Coat 2 for 36 days@21ºC. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'K-TANK Panel'. Light grey coloured, hot press moulded GRP panel. For use with water up to 60°C.
'Sinopec Water Pipeline Joint Lubricant (Si) (product code: 509164)'. Clear, translucent silicone base lubricant. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'ULTRAMID B3E2G6 AQUA GREY 7118'. Grey coloured, injection moulded PA6 material. For use with water up to 85°C.
'Grilamid TR 60 natural'. Natural (appears amber coloured), injection moulded polyamide material. For use with water up to 85°C.
'Yildiz Polietilen Electrofusion and Spigot Fittings'. Black coloured, injection moulded HDPE Electrofusion and Spigot fittings. For use with water up to 60°C.
'THERMOTECH HDPE Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'Techniplast PE100 Pipes'. Black coloured (with blue stripe), extruded PE100 pipes. For use with water up to 60°C.
Page 328 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
