‘Sikalastic®-6100 FX White’ (formerly known as ‘MasterSeal 6100 FX White’) ‘Sikalastic®-6100 FX Grey’ (formerly known as ‘MasterSeal 6100 FX Grey’. Site applied, two-component cementitious coating. Mix ‘Sikalastic®-6100 FX White’ (Coat 1) with water in a mass ratio of 15:5.6. Apply and cure for 1 day@5°C before applying Coat 2. Mix ‘Sikalastic®-6100 FX Grey’ (Coat 2) with water in a mass ratio of 15:5.6. Apply and cure for 5 days@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquakote Grey for use with Aquakote Blue'. Site applied, blue coloured (once applied), two-component epoxy coating. 'Aquakote Grey’ is the base coat and comprises of Parts A (grey liquid) & B (amber liquid) which are to be mixed in a 100:17 mass ratio and then applied in a wet film thickness of 200µm. Cure for 12 hours@10°C before applying top-coat. 'Aquakote Blue’ is the top-coat and comprises of Parts A (blue liquid) & B (amber liquid) which are to be mixed in a 100:17 mass ratio and then applied in a wet film thickness of 200µm. Cure for 12 hours@10°C. For use with water up to 23°C. Please note that 'Aquakote Grey & Aquakote Blue' are to be used in conjunction with each other. the approval does not cover 'Aquakote Grey and/or Aquakote Blue' when applied as a single coat.
`Ruby Veg Soft Soap/EasyJoint Uni`. Translucent, amber coloured, soya oil lubricant. Apply as per manufacturer's technical datasheet 'revision 2' dated '22/09/21'. For use with water up to 23°C.
'CELANYL A2 WR GF30 NC 1102/2A & CELANYL A2 WR GF30 NC 1102/2B'. Off-white, injection moulded nylon materials. For use with water up to 85°C.
'Badadur PBT8 GK30 Graphit 371'. Grey coloured, injection moulded PBT material. For use with water up to 65°C.
'POLYPOL-1052'. Pale yellow/beige coloured, isophthalic unsaturated polyester resin material. For use with water up to 50°C.
'Avaspire AV-621 NT'. Natural (appears beige, opaque), injection moulded PEEK material. For use with water up to 85°C.
'VICTREX' injection moulded PEEK thermoplastic materials. For use with water up to 85°C. VICTREX PEEK 450GL30, 450G, 450FE20 (natural – appears beige coloured), 450FC30, 450CA30 & 90GL30BLK-EU (black coloured). VICTREX FG™100, FG™120, FG™200, FG™220, FG™300 & FG™ 325 (natural – appears beige coloured). VICTREX FG™101, FG™121, FG™140, FG™201, FG™221, FG™240, FG™301 & FG™320 (black coloured). VICTREX FG™340 (dark grey coloured).
'SP-01 HDPE Fitting'. Black coloured, injection moulded HDPE fittings. For use with water up to 23°C.
'Revolve N-525 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Total 3581 Blue Polyethylene & Total 3581 Black Polyethylene'. Blue or black coloured, polyethylene material manufactured by rotational moulding. For use with water up to 65°C.
'Total 4041 Blue Polyethylene & Total 4041 Black Polyethylene'. Blue or black coloured, polyethylene material manufactured by rotational moulding. For use with water up to 65°C.
'CONTINUUM DGDA-2610 BK'. Black coloured, compression moulded HDPE (PE100) material. For use with water up to 23°C.
'TP11115 Prisma Black'. Black coloured LLDPE material manufactured by rotational moulding. For use with water up to 70°C.
'F420B00 natural (appears off-white), F420B99 (black coloured) & F410K01 (white coloured)'. Injection moulded, glass filled polypropylene materials. For use with water up to 85°C.
'Chemfix 10'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 600'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '11/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EX1'. Site applied, grey coloured (once mixed), two-component anchor resin. Mix, apply and cure as per manufacturer's product information 'EX1 V2.08' Issued '08/2021' (refer to working and loading times table for cure). For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`1025 Titan Bladder`. Black coloured, calendared butyl rubber sheet material. Shore hardness 60. Tested in-radius size 0.5mm. For use with water up to 23°C.
'ERIKS 55985 Gaskets & ‘O’ rings'. Black coloured, compression moulded EPDM gaskets & ‘O’ rings'. Shore hardness 70A. The gaskets have a tested in-radius size of 1.0mm. The ‘O’ rings have a tested in-radius size of 1.76mm. For use with water up to 85°C.
`RG EP W80`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'SEAEP80N01'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80A. Tested in-radius size 1.55mm. For use with water up to 85°C.
'E8121'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80A. Tested in-radius size 1.55mm. For use with water up to 85°C.
'S-9028'. Black coloured, compression moulded EPDM rubber material Shore hardness 60 ShA. Tested in-radius size 1.0mm. For use with water up to 60°C.
'E701/A'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 23°C.
'0713.17/55 (shore hardness 55) & 0713.17/70 (shore hardness 70)'. Black coloured, compression moulded EPDM rubber materials. Tested in-radii size 1.1mm. For use with water up to 23°C.
'OLDAL VMQ880 65TR – VMQ4303'. Colourless (translucent), extruded VMQ rubber material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SB1 Bonding Agent'. Factory applied, black coloured bonding agent intended to bond plastic or brass to rubber. Apply and cure as per manufacturer's instructions 'LDAP-003 issue 1' dated 11-08-2016. For use with water up to 85°C.
'581189 Center Jet Blue Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Mega All White'. White coloured (opaque) anaerobic sealant/adhesive. Apply in strict accordance with manufacturer's instructions 'issue 01' dated '09/09/2021'. For use with water up to 85°C.
'Ixef DW 1022 BK001 & Ixef FC-1022 BK001'. Black coloured, injection moulded polyarylamide materials. For use with water up to 85°C.
‘Thermolast K TF(1)WCS (natural) and Thermolast K TF(1)WCS-917 (black)’. Injection moulded TPE materials available in natural (appears cream) or black. Shore hardness between 60 & 90. Tested in-radius size 1.0mm. For use with water up to 23°C. (1) Indicates the shore hardness 6=60 shore, 7=70, 8=80 & 9=90.
'ULTEM', injection moulded polyetherimide materials. For use with water up to 85°C. PW1000-1000, PW1000-1000 and PW1000-1000W (yellow coloured). PW2100-1000, PW2100-1000 and PW2100-1000W (brown coloured). PW2200-1000 & PW2300-1000 (beige coloured). PW2400-1000 (grey coloured). PW1000-7101, PW2100-7301, PW2100-7301, PW2100-7301W, PW2200-7301, PW2300-7301 & PW2400-7301 (black coloured). ULTEM PW2300-1000 and ULTEM PW2300-1000W were added to the approval in June 2025.
'Hytrel® HTR6108'. Translucent cream coloured, injection moulded thermoplastic elastomeric material. Shore hardness 61. For use with water up to 85°C.
BS1212-4 (2016) compact type float operated valve for WC flushing cisterns, side entry type. The inlet incorporates a plastic flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of WC flushing cisterns incorporating a BS 1212-4 (2016) side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres or 4.5/3 litre flush volumes. The cistern is operated by a manual push button and the product incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Type TK, spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-verifiable single check valve assembly consisting of a spring loaded, resilient trim, single check valve cartridge with a brushed chrome DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Non-rising spindle headwork incorporating a brass body and NBR ‘O’-rings to be inserted into specifically dimensioned bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 85°C.
Range of ceramic disc headworks with brass bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Quarter turn ceramic disc headwork incorporating a plastic body to be housed in specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
A ceramic cartridge headwork with a plastic body and EPDM ‘O’-rings for insertion into specifically dimensioned assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Thermostatic cartridge incorporating a plastic body, stainless steel strainer and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Page 33 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
