Section Code 1530 :
Back To Directory SectionsRange of flow sensors with plastic bodies and rotors. Maximum working pressure: 10 Bar. Maximum operating temperature: 80°C.
Range of EEICo brass threaded fittings. Maximum working pressure 20.0 bar. Maximum operating temperature 60°C.
Range of stainless steel bodied mechanical pump shaft seals. The 491 model comprises of carbon and silicone carbide seal faces and EPDM ‘O’-rings. The 1510 model comprises of carbon and silicone carbide seal faces, EPDM ‘O’-rings and an orange NBR/aramid fibre gasket. Maximum operating temperature 100°C.
Range of self-acting controllers with brass bodies, EPDM O rings and gaskets. Maximum working pressure 16.0 Bar Maximum operating temperature of the secondary circuit is 65˚C and the primary circuit is 99˚C
Range of flow-compensated (thermostatic) temperature controllers incorporating a brass body with EPDM ‘O’-rings and gaskets. The valves incorporate a non-rising spindle headwork for temperature regulation. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C
Range of concealed rough-in sets with brass bodies, intended for use in conjunction with trim and finish sets. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Range of submersible pressure sensors and hydrostatic transmitters (supplied in lengths up to 1000m). Cold water use only.
Arrangement of PVC-U pipe and fittings for use with the Orca System. Maximum working pressure 9.0 bar. Cold water use only.
Range of brass bodied differential angled bypass valves incorporating a spring-loaded adjustment facility. Maximum working pressure 10.0 bar. Maximum operating temperature 110°C.
Combined bath filler and overflow waste assembly with a plastic body (various finishes - see model). The product incorporates a click type pop-up waste. Maximum operating temperature 85°C.
Flow restriction valve with a brass body. Maximum working pressure 35.0 bar. Maximum operating temperature 85°C. For non-wholesome water use only.
Range of differential pressure sensors with stainless steel bodies. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of tap outlets with chrome plated plastic bodies. Maximum operating temperature 85°C.
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of VEGAPULS radar sensors for level measurement with plastic bodies. Cold water use only. Open outlet use only.
Range of ‘Thermowatt’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
`Prox’ and ‘Wave` ranges of sensor operated flow control devices incorporating a normally closed solenoid valve to control the flow and operated via an infra-red sensor. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8 Bar Maximum operating temperature 65°C
Range of leak detection devices incorporating a DZR brass body and non-return valve (not intended for and not suitable for backflow protection). Models Stopleak 1 & Stopleak 2 incorporate a spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall brackets (brass bodies – various finishes). Open outlet use only Maximum working temperature 85°C
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Hydraulic circuit used to control the water path within the heating and sanitary boiler, with plastic body incorporating filter, flow regulator, plate heat exchanger and EPDM O-rings. Maximum working pressure 7.0 bar. Maximum operating temperature 85°C.
Manifold with a brass body and 5 outlets. Maximum working pressure 15.0 bar. Maximum operating temperature 100°C.
Wall plate elbow with a brass body. Maximum operating temperature 100°C
Range of leak detection devices incorporating a DZR brass body and non-return valve (not intended for and not suitable for backflow protection). Models 3897590 & 3897690 incorporate a spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Electroflo sensor operated flow control devices incorporating a normally closed solenoid valve to control the flow and operated via an infra-red sensor. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8 Bar Maximum operating temperature 65°C
Range of test port assemblies with DZR brass bodies. Maximum working pressure 25.0 Bar. Maximum operating temperature 100°C.
Nova-Flo’ inline flow control device with a plastic body. The product is intended to restrict the flow of water to a bath or basin if water level reaches the overflow. Float located within the overflow pathway activate flaps on each inlet to restrict the flow prior to the taps being closed. Maximum working pressure: 12 Bar. Maximum working temperature: 60°C.
Range of plastic pressure sensors. Maximum working pressure: 15.99 Bar. Maximum operating temperature 90.0°C.
Bias chamber incorporating an EPDM diaphragm and ‘O’-ring with a brass body. Maximum working pressure 35.0 bar. Cold water use only.
Range of electronic pump controllers with plastic bodies. Maximum working pressure 12.0 Bar. Cold water use only.
Range of pressure transducers with stainless steel bodies. Maximum working pressure 10.0 Bar, 20 Bar or 40 Bar. Maximum operating temperature 99°C.
Mixing valve incorporating a brass body and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure10.0 bar. Maximum operating temperature 65°C.
Direct coupler (brass with a range of finishes). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of Fastec® F13 and Fastec® F14 fittings for use with Fastec® manifold assemblies, incorporated with brass bodies and EPDM O-rings. To be used with copper pipe complying with BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of spherical valves with a DZR brass body and lever. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall brackets (brass bodies – various finishes). Open outlet use only Maximum working temperature 85°C
Range of flexible joints incorporating an EPDM (inner & outer) joint with a steel reinforcing ring and two carbon steel flanges. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of accumulators. The brass vessel connector of the ACC-060-TNK, ACC-120-TNK and ACC-180-TNK models incorporates a plastic flow regulator. Maximum working pressure 8.6 bar. Cold water use only.
Top entry compression cylinder flange with DZR brass body and copper anti-aeration dip tube. The compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 4.0 bar. Maximum operating temperature 60°C.
Leak detection system, comprising of a flow sensor with a stainless-steel body incorporating a motorised spherical valve, with a stainless-steel ball. Please note that claims of leak detection have not been verified by WRAS. Maximum working pressure 15.0 bar. Maximum operating temperature 85°C.
Brass flow meter and smart box water monitoring system. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
Range of installation kits comprising of a water block, double check valve assembly (suitable for backflow protection against fluid category 3) and a pressure reducing valve (outlet pressure range 3.0 to 3.5 bar). Model 95428 incorporates a water filter. Maximum working pressure: 16 Bar Maximum operating temperature: 23°C
Ranges of sensor operated flow control devices either mains or battery powered, incorporating a normally closed solenoid valve to control the flow and operated via an infra-red sensor. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8 Bar Maximum operating temperature 65°C
Stainless steel pressure transducer. Maximum working pressure 20.0 Bar. Maximum operating temperature 50.0°C.
Range of ‘Tcontrols’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
Plastic turbine for insertion into specifically dimensioned flow meters. Maximum operating temperature 85°C. Open outlet use only.
Electronically controlled advanced flow control pilot valve assembly with stainless steel body. Maximum working pressure 16.0 Bar Cold water use only.
Range of flow restriction blocks with a stainless-steel body and integral stainless-steel filter. Maximum working pressure 16.0 Bar Cold water use only.
Page 4 of 5
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
