Range of pilot operated, adjustable, pressure reducing control valves with blue epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, three spherical valves and a needle valve. Maximum supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 2.0 – 12.0 bar. Maximum operating temperature 80°C. Above ground use only.
Range of inline brass bodied or chrome plated brass bodied spherical valves, with a chrome plated brass ball and EPDM ‘O’-rings. SVB66MB and SV44MB models are lever operated. SV66MBC and SVT64MBC are screwdriver operated. The products are for use with PE-X pipe (manufactured to BS 7291-3), PB pipe (manufactured to BS 7291-2) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of spherical valves with nickel plated brass bodies, brass ball and PTFE seats. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of electrically operated motorised spherical valves incorporating brass bodies and stainless-steel balls. Maximum working pressure 20.0 bar. Maximum operating temperature: 85°C.
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets and Bronze body, bronze wedge and handwheel. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and discs with PTFE seals. The valves operate via a non-rising spindle headwork that incorporates a wheel type operating member. Maximum working pressure; 20 Bar Maximum operating temperature; 85°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies and EPDM wedges. Maximum working pressure 10.0 Bar or 16.0 Bar Maximum operating temperature 40.0°C
Range of gate valves with brass bodies, brass wedges and PTFE gaskets. The valves are operated via a non-rising spindle with a hand wheel operating member. The Z2020.028 compression model is for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with brass bodies, brass wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves incorporating brass or bronze bodies and EPDM gaskets. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of inline plastic bodied screw down stop valves incorporating a non-rising spindle headwork with a dome type operating member. The products are for use with PE-X pipe (manufactured to BS 7291-3) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of UV disinfection units with stainless steel bodies and quartz tubes. Maximum working pressure 10.0 bar. Cold water use only.
'PENTANOL DI 8055 BLACK'. Factory applied, black coloured Bitumen based coating. Apply as per manufacturer's TDS 'January HD 2024'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.3 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver2 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 285 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
