Pillar tap (chromium plated brass), incorporating quarter turn ceramic disc with single lever operating members and metal backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 6.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of nylon braided (DG50X model series) or stainless steel braided (DG10X model series), PEX lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of stainless-steel interlocked shower hoses and shower hose extension pieces (smaller length versions) incorporating PE/EPDM and PEX inner tube materials. Available with various surface finishes and end connectors. For further details see model section. Maximum working pressure open outlet use. Maximum operating temperature 85.0°C
Range of nylon braided (DG50E model series) or stainless steel braided (DG10E model series), EPDM lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of cased and insulated stainless steel unvented water storage heaters. The DHW circuit includes a factory fitted combined temperature and pressure relief valve set at 6.0 bar and 90˚C. The product can be supplied with two possible safety kits (inlet control groups). One includes a pressure reducing valve adjustable between 1.5-6.0 bar, (but set at 3.0 bar), a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) and a pressure relief valve pre-set at 4.5 bar. The other includes a pressure reducing valve pre-set at 3.0 bar, an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, and a pressure relief valve pre-set at 4.5 bar. The product is also supplied with an expansion vessel and a tundish. The compression connection of each inlet control group is for use with the following pipes: Both for use with copper pipe (manufactured to BS EN 1057). The inlet control group without an adjustable pressure reducing valve can also be used with PB pipe (with inserts) (manufactured to BS EN 7291-2:2010) and PEX pipe (with inserts) (manufactured to BS EN 7291-3:2010). Maximum supply pressure to inlet control group pressure reducing valve: 16.0 bar. Maximum working pressure 4.0 bar. Maximum operating temperature 99°C. Cold supply only.
Wall mounted, manually operated blending shower valve with (brass bodies - various finishes) incorporating a ceramic cartridge headwork and a single lever operating member. The shower outlet connection incorporates an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature 70.0°C
Range of concealed, wall mounted thermostatic blending valves with brass bodies (chromium plated trim set). The product incorporates a ¼ turn ceramic disc or a 2 way manual diverter with shut-off position to control the flow, with dome type operating members.The temperature is controlled independently via thermostatic cartridges, with dome type operating members. The inlets incorporate approved check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure: 5 Bar. Maximum operating temperature: 60°C.
Wall mounted concealed three way diverter valve assembly (brass bodies with trim sets in various finishes). Maximum working pressure 10 bar. Maximum operating temperature 70°C
Range of wall mounted exposed shower valves (Brass bodies – various finishes), incorporating single sequential headworks controlling both flow and temperature with single a single lever operating member. Models (BPMO SHXVO C & BPRR SHXVO C) incorporate non-rising spindle headworks controlling the flow with single lever operating members. The temperature is controlled independently via a thermostatic cartridge with cross-top operating members. The inlets incorporate flow regulators, plastic strainers and approved single check valve cartridges however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Models (Mini TS1203 RR C, R2 SHXRR C & KN2 SHXRR C) are supplied with riser rails and overhead shower outlets. Models (R2 SHXVO C, BPRO SHXVO C & BPMO SHXVO C) valve only. All other models are supplied with shower hose, handset and riser rail assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Page 285 of 408
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
