Range of spherical valves with stainless steel bodies, stainless steel ball and lever operating members. The press-fit connection is for use with stainless steel pipe (manufactured to EN10312). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves, with DZR brass bodies and chromium plated brass balls. The products can be supplied with various operating members (see model). Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of plastic bodies spherical valves (black, white and grey) incorporating either a screwdriver slot, lever or handwheel operating member (model specific). The pushfit connections are for use with DM LLDPE tubing (not supplied) and PEX barrier pipe (manufactured to BS7291-3). When used with DM LLDPE tubing (not supplied) the supplied black or grey pipe inserts must be installed. When used with PEX barrier pipe the supplied beige pipe inserts must be installed. Maximum working pressures and temperatures: When used with DM LLDPE tubing: Grey body valves, for sizes 6-15mm and ¼”-½” pushfit: 12.0 bar, cold water use only. Grey body valves, for sizes 6-12mm and ¼”-½” pushfit: 7.0 bar @ 65°C. Black and white body valves, for sizes 6-15mm and ¼”-½” pushfit: 12.0 bar, cold water use only and 7.0 bar @ 65°C. When used with PEX Barrier pipe (manufactured to BS7291-3): Grey body valves, for sizes 15-22mm, 5/8” and 7/8” pushfit: 12.0 bar, cold water use only. Black and white body valves, for sizes 15-22mm, 5/8” and 7/8” pushfit: 12.0 bar, cold water use only and 7.0 bar @ 65°C. All fittings which incorporate a barbed end connection are open outlet use only.
Range of gate valves with brass bodies and wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Flomasta Range of plastic, push-fit stop valves for use with MDPE pipe (manufactured to BS EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
Water filter and scale inhibitor comprising of a plastic filter head and plastic filter cartridge with an activated carbon block and sodium polyphosphate. The push-fit connections are for use with LDPE pipe (manufactured to DIN 8072). Maximum working pressure 5.52 bar. Cold water use only.
UV Home’ range of UV disinfection units with 304L or 316L stainless steel bodies (see models). Maximum working pressure for UV HOME 2 & 3 is 6 bar. Maximum working pressure for UV HOME 6 & 9 is 10 bar. Maximum operating temperature 35°C.
'ABS 727-Grey (grey coloured), ABS 727-Dark Grey (dark grey coloured), ABS 727 GR48 (grey coloured), ABS 727 White (white coloured), & ABS 727 Black (black coloured)'. Injection moulded ABS materials. For use with water up to 85°C.
'CER4'. White coloured ceramic disc manufactured by dry-press. For use with water up to 85°C.
'Powercron 805 B'. Factory applied, blue coloured Acrylic coating. Apply as per manufacturer's TDS 'CR805B/CP826', dated 'Sep 12, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron 451B'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's TDS 'CR451B/CP573X', dated 'Sep 24, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/004', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'M-AC010'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user manual 'rev. 2.0R' dated 10/10/2024. Cure for 20 minutes at 180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Fusion Bonded Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HX' dated '2025.4.25'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VETOPROOF EC720'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 84.8:15.2 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1104-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'VETOPROOF EC722'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 85.4:14.6 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1101-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Radilon A RCM4010RKC 306 BK'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 85°C.
'UP 5604 TP' (amber coloured) & 'UP- 4601 TPI' (pink coloured). Unsaturated polyester resin materials manufactured by hand lay-up. For use with water up to 50°C.
‘Polytank 4 Layer Multilayer LLDPE Tank Panel'. Multi-layered LLDPE tank panel, manufactured by rotational moulding, consisting of a white coloured inner layer, light grey coloured second layer, black coloured third layer & white coloured outer layer. For use with water up to 65°C.
'Fortron ICE 504L SD 3039 black (DW)'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
Page 278 of 310
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
