'Endoprene 888.56'. Factory applied, beige coloured, two-part PU coating. Mix Parts A & B in a 75:25 volume ratio and apply as per Technical Data Sheet dated 09/12/2020. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'181019 Epoxy Phenolic RAL 5012'. Factory applied, blue coloured epoxy phenolic powder coating. Mix and apply as per manufacturer's instructions issued '15.01.2023'. Cure for 10 minutes at 200°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925 Cream'. Site applied, cream coloured, two-component, solvent free epoxy coating. Mix part A (white liquid) with part B (yellow liquid) in a volume ratio of 3:1 and apply as per manufacturer’s TDS ref. ‘2252’ dated 17/12/2020. Cure for 7 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eltex TUB124N2025'. Blue coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex Superstress TUB121N6000'. Black coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex TUB121'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'ELTEX Superstress TUB121N3000'. Black coloured, extruded polyethylene material. For use with water up to 23°C.
'Monotape 12, 24 B, 24 BB, 24 HD & 25 BI'. White coloured PTFE tapes manufactured by extrusion, stretching and calendaring. '24 SH, 20SH, 30SH & 28LS-LE'. White coloured PTFE gasket sheets manufactured by extrusion, stretching, sintering and calendaring. For use with water up to 85°C.
'STRONGHOLD SH-EP3'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EPDM C12251'. Black coloured, compression moulded, EPDM rubber material. Shore hardness 77. Tested in-radius size 12.5mm. For use with water up to 23°C.
'EP601289C'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (brass body, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout incorporates an integral plastic flow regulator and a plastic aerator. The product is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of flow restrictors with plastic bodies and EPDM ‘O’-rings available in a variety of colours (see models). Maximum operating temperature 60°C.
'PCR-E' range of flow regulators with chrome plated brass housing and NBR sealing gaskets. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet is a pull-out spray type. The spout inlets incorporate approved check valve cartridges; however, the complete assembly has not been tested to demonstrate it provides backflow prevention. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
‘Edition 400’ range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with asingle lever operating member. The spout outlet incorporates a plastic aerator. The products can be supplied with or without a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating non-rising spindle headworks with dome type operating members for models (101221) and a cross-top operating member for model (101229 Henlake basin mixer ). Model (101226 Lever basin mixer ) incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporates a stainless steel strainer and plastic flow strainer or a plastic aerator. The products are supplied with a click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener (TR1025 and TR1026 models) or a plastic aerator (all other models). The products are supplied with or without a click type pop-up waste (see model). Maximum operating pressure: MINI models 10.0 bar, all other models 5.0 bar. Maximum operating temperature 65°C.
Page 28 of 124
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
