Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves with brass bodies, brass wedges and PTFE seals. The valves operate via a non-rising spindle and are supplied with either no operating member or a hand wheel (see models) Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range rising spindle screw down stop valves with gunmetal bodies and T-type operating members. Models 41020, 41025, 41032, 31050 models are to be used with PE80 pipe manufactured to EN 12201. Maximum working pressure: 12.5 Bar. Maximum operating temperature: 23°C.
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves with bronze bodies, DZR brass discs, EPDM `O`-rings and PTFE disc face. The valves incorporate a non-rising spindle headwork regulating the flow and isolation function. The D931, D933 and D934 models incorporate two pressure test points. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
'ULTRAFORM® N4320 003 AT UNCOLORED'. Natural (appears white), injection moulded POM material. For use with water up to 85°C.
'LM-coat'. Factory applied, blue coloured, two-part Polyurea coating. Mix Part A (KOBECASE PS-6031) with Part B (COBENATE I-362) in a 100:100 volume ratio and apply as per manufacturer's TDS 'Rev. no: 02', dated '16.02.2022'. Cure for 4 hours@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PolyQuick® P-500 PW'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 05-2025'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SOLID-01'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35 and apply as per manufacturer's User Instructions 'SOLID-196', 'Vision: A-2', dated '2019-8-28'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOD-E-2024/1'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions 'T264', revision '00', dated '16.07.2024'. Cure for 25 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TIANYI SUNS-011'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35 and apply as per manufacturer's User Instructions 'Tianyi Suns-0023', version 'TYS-02', dated '2021-05-04'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SikaTop®-107 Seal AE'. Site applied, grey coloured, two-part coating. Mix parts A and B in a 1.4 weight ratio and apply as per manufacturer's Method Statement 'V1', dated 'Feb 2025'. Cure Coat 1 for 3 hours at 30°C. Cure Coat 2 for 21 days at 30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Evercrete Vetrofluid'. Site applied, colourless, cement waterproofing liquid. Apply two coats as per manufacturer's instructions dated '01 JULY 2024'. Cure Coat 1 for 4hrs 40mins@21ºC and Coat 2 for 36 days@21ºC. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM AC'. Site applied, grey coloured cement mortar. Mix 'NATCEM AC' and water in a weight ratio of 5:1 and apply as per manufacturer's Instructions for Use 'Issue 4', dated '16 September 2024'. Cure for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sinopec Water Pipeline Joint Lubricant (Si) (product code: 509164)'. Clear, translucent silicone base lubricant. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'AMIANTIT HDPE Pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 50°C. Please note that only pipes marked with 'HE3490' are covered by the scope of the approval.
'7644'. Black coloured PE foam tape to be applied as per manufacturer's instructions. For use with water up to 23°C.
'NORYL WM300G-701 (black), NORYL WM300G-960 (grey), NORYL WM300G-801 (beige) & NORYL WM300G-845 (beige)'. Injection moulded PPE+PS materials. For use with water up to 85°C.
Page 264 of 310
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
