'EW Gasket Material'. Black coloured EPDM gasket material which is injection moulded and then spliced. Shore hardness 65A. Initial tested in-radius size 3.9mm. In March 2023, the tested in-radius size was increased to 4.4mm. For use with water up to 23°C.
'E65-04BL-G / Black'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 23°C.
'EPDM 1570'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 23°C.
'MRP-EN-50, MRP-EN-55, MRP-EN-60, MRP-EN-65, MRP-EN-70, MRP-EN-75 & MRP-EN-80'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50 & 80. Tested in-radius size 0.88mm. For use with water up to 65°C.
‘VF75GRN seals & ‘O’ rings’. Green coloured, injection moulded fluoroelastomer `O` rings & seals. Shore hardness 75. The ‘O’ rings have a tested in-radius size of 1.0mm. The seals have a tested in-radius size of 5.5mm. For use with water up to 85°C.
'3272 Washers & 'O' rings'. Green coloured, injection moulded FKM washers & 'O' rings. Shore hardness 70. The washers have a tested in-radius size of 0.75mm. The 'O' rings have a tested in-radius size of 1.31mm. For use with water up to 85°C.
'WN1743 BLK O-rings & gaskets'. Black coloured, injection moulded NBR 'O' rings & gaskets. Shore hardness 50. The 'O' rings have a tested in-radius size of 1.5mm. The gaskets have a tested in-radius size of 0.7mm. For use with water up to 23°C.
'Membrane R219 34 9513 NBR 55 Sh'. Black coloured, injection moulded NBR rubber membrane. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 23°C.
'NB751359C'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
'N7018AA'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
'ME2020/80 Grey'. Grey coloured, injection moulded VMQ sheet material. Shore hardness 80. Tested in-radius 1.0mm. For use with water up to 85°C.
'RLC+'. Orange coloured (translucent) anaerobic adhesive. Apply and cure as per manufacturer's Technical Data Sheet, version 1 issued on 03/11/2022. For use with water up to 23°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'Tangit ABS'. Grey coloured solvent cement. Apply as per manufacturer's Technical Data Sheet 'Tangit ABS TDS 072017 EN'. Cure for 20 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer and check valve cartridge(s), verified by test (suitable for backflow protection against Fluid Category 2). The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the spout to the solenoid. The spout outlet incorporates a plastic aerator. Maximum working pressure - 10 Bar Maximum operating temperature - 60 °C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 1.0 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) electronically controlled tap assemblies. The flow and temperature is controlled by a ceramic cartridge headworks with single lever operating members. The flow is also controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The hose inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water only
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a plastic strainer. Maximum working pressure 10.0 Bar. Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 5.5 litres and a reduced flush of up to 2.7 litres and incorporates a servicing valve and flexible hose on the inlet supply. The cistern is operated by a manually operated push button. Maximum working pressure 10.0 bar. Cold water use only.
Page 250 of 554
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
