Range of ball valves with DZR brass bodies and either a chrome plated DZR brass ball (¼-1" sizes) or stainless-steel ball (1¼-2" sizes). The valves are available with lock shield, butterfly or single lever operating members. The threaded end connections have octagonal spanner flats. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with brass bodies (chromium plated), incorporating chromium plated balls and PTFE seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with DZR brass bodies, stems and discs. The valves operate via a hand wheel (non-rising) and a metal to metal seal. Valves are for above ground use only. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of ductile iron gate valves with blue epoxy coated bodies, EPDM wedges and EPDM O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves with blue epoxy ductile iron bodies and wedges incorporating PTFE seals and a non-rising spindle (16Q models) or outside screw and yoke (125Q models). The valves incorporate a handwheel operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of gate valves incorporating blue epoxy coted ductile iron bodies, ductile iron wedges encapsulated in EPDM and an EPDM gasket and seal. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass bodies, NBR seals and ‘T’ type operating members. Compression connection to be used with copper pipe EN1057 only. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of commercial washing machines with flow controlled by solenoid valves and discharged via type AB air gap assembly (verified by test - suitable for backflow protection against fluid category 5). The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5 Bar. Maximum operating temperature 60°C.
ClearScale Plus range of in-line water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
'DURACON® EX-09 WK2001' & 'EX-09 WK2001BG'. White coloured, injection moulded acetal materials. For use with water up to 85°C.
'POLYLAC® PA-777D'. Natural (cream coloured), injection moulded ABS material. For use with water up to 85°C.
‘POLYLAC® PA-757F'. Natural (cream coloured), injection moulded ABS material. For use with water up to 85°C.
‘POLYLAC® PA-747'. Natural (beige coloured), injection moulded ABS material. For use with water up to 85°C.
'ELECTROCOAT BP 1119'. Factory applied, black coloured Bituminous Paint. Apply as per manufacturer's TDS Document No: 'ECL/ TDS / BP-1119-Bituminous Paint', Issue Date '10-Aug-20', Version No: '01'. Cure for 12 minutes at 45°C, followed by 10 hours at 28°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CD 101 Grey Sealing Disc'. Grey coloured ceramic disc component manufactured by powder pressing, sintering and grinding. For use with water up to 85°C.
'Rubalit A1896 Sealing Disc'. White coloured ceramic disc component manufactured by powder pressing, sintering and grinding. For use with water up to 85°C.
'AK-SSIC'. Grey coloured, sintered silicon carbide ring component. Between January 2024 and March 2024, the component is for use with water up to 23°C. From April 2024, the component is for use with water up to 85°C.
'JBG-SRPC Plus'. Factory applied, sulphate resisting Portland cement intended to line ductile iron pipes. Mix sand:cement:water in a 3:2:1 ratio and apply as per manufacturer's instructions 'JBIL/IFU-01' dated '29.01.2024'. Cure for 28 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JBG-OPC Plus'. Factory applied, grey coloured, ordinary Portland cement intended to line ductile iron pipes. Mix sand:cement:water in a 3:2:1 ratio and apply as per manufacturer's instructions 'JBIL/IFU-01' dated '29.01.2024'. Cure for 28 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NATZINC EP9015 SC PART A-BI.5431 Primer for use with HYDRALFUN AC BLEU PAM RAL5005-CZL8190 Coating’. Factory applied, dark blue coloured (once applied), powder coating for use with two-part epoxy primer. Mix parts A & B of primer in a 100:10 mass ratio and apply as per manufacturer’s TDS dated February 2024. Cure for 24 hrs at 20°C. Apply coating as per manufacturer’s TDS dated February 2024 and cure for 21 days at 20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 233 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
