Directory Search Results

Print List

#2011358

Range of heat interface units (HIU) with either twin or single stainless steel copper brazed plate heat exchangers (depending on model) providing heating and hot water (twin unit) hot water only, or heating only. The hot water is generated via a plate heat exchanger. The primary (space heating) circuit incorporates an expansion vessel and a pressure relief valve (set at 3.0 bar). The product incorporates a CAb backflow prevention device (suitable for backflow protection against Fluid Category 3) for filling the heating circuit. The inlet and outlet of all circuits incorporate a lever operated spherical valve. Maximum working pressures and operating temperatures: Primary (district heating): 10.0 bar and 85˚C. Domestic hot water (DHW): 10.0 bar and 60˚C. Secondary (space heating): 2.5 bar and 80˚C.

Section:
1465 Heaters
Section Subtitle:
Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:
2011358
Size:
22mm solder fitting
Marking:
Albion water management, model and other tech info on data label on the side panel.
Installation Requirements:
R001 R140
Expiry date:
30/11/2025
Model:
[Twin Unit]: Standard Twin Plate – heating with 24 plates and hot water with either 14 or 40 plates. Heating connection to cold water by filling loop. Products: TH000240 MTA TWIN 24-40 TH000214 MTA TWIN 24-14 TH001240 MTA TWIN 24-40 HM TH001214 MTA TWIN 24-14 HM [Hot Water Only]: Hot water with either 14 or 40 plates, connection direct to cold water. Products: TH000414 MTA HOT WATER ONLY 00-14 TH000440 MTA HOT WATER ONLY 00-40 TH001414 MTA HOT WATER ONLY 00-14 HM TH001440 MTA HOT WATER ONLY 00-40 HM [Heating Only]: Heating with 40 plates on domestic heating circuit only, connection to cold water via filling loop. Products: TH000340 MTA HEATING ONLY 40-00 TH001340 MTA HEATING ONLY 40-00 HM ‘HM’ stands for heat meter which is on the heating circuit
Product Images

Approval Holder:
Albion Water Management
Company Name
Albion Water Management
Address
30-31 Station Close, Potters Bar, Hertfordshire
Postcode
EN6 1TL
Phone
01707 607230
General Email
water@albiongroup.co.uk

View All Listings by this Company
Manufacturer:
Albion Water Management
Company Name
Albion Water Management
Address
30-31 Station Close, Potters Bar, Hertfordshire
Postcode
EN6 1TL
Phone
01707 607230
General Email
water@albiongroup.co.uk

View All Listings by this Company

Print This Approval


#2012012

Range of multi-layer shower hoses with a PVC inner hose, supplied with EPDM ‘O’-rings. Maximum operating temperature 60°C.

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
2012012
Note:
Open outlet use only.
Marking:
Solex, WRAS and date of manufacture (MM/YY) on captive nut.
Installation Requirements:
R001
Expiry date:
31/12/2025
Model:
H21X0008S-01 - ½” BSP (F) conical or captive nut. H21X0008S-02 - ½” BSP (F) conical or captive nut. Models added November 2021: H21X0007S-01 - ½” BSP (F) conical or captive nut. H21X0007S-02 - ½” BSP (F) conical or captive nut. H21X0007S-03 - ½” BSP (F) conical or captive nut. H21X0007S-04 - ½” BSP (F) conical or captive nut. H21X0007S-05 - ½” BSP (F) conical or captive nut.
Product Images

Approval Holder:
Xiamen Solex High-Tech Industries Co., Ltd.
Company Name
Xiamen Solex High-Tech Industries Co., Ltd.
Address
No. 298 Yangguang Road West, Haicang District, Xiamen, Fujian Province, 361022
Country
China
General Email
brian_lin@mysolex.com

View All Listings by this Company
Manufacturer:
Xiamen Solex High-Tech Industries Co., Ltd.
Company Name
Xiamen Solex High-Tech Industries Co., Ltd.
Address
No. 298 Yangguang Road West, Haicang District, Xiamen, Fujian Province, 361022
Country
China
General Email
brian_lin@mysolex.com

View All Listings by this Company

Print This Approval


#2012359

502 series of automatic air venting valves with brass bodies, plastic float and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 115°C. Model added September 2021 (501500) has a maximum operating temperature of 120°C. All other models have a maximum operating temperature of 115°C.

Section:
1980 Valves
Section Subtitle:
Air venting. Fittings in this section are suitable for above ground installations only.
WRAS Approval Number:
2012359
Size:
See model
Marking:
Caleffi logo on body.
Installation Requirements:
R001 R200
Expiry date:
31/12/2025
Model:
Serie 502 Robocal: ⅜" BSP (M): 502430. 502430 CON. 502430 CST. 502431 BSC. 502434 CST. 502435 CST. 502533. 502533 FRT. 502533 RIF. 502533 TAK. 502934 CST. 502937 BSC. Art. 502 Robocal with flow valve: ¼" BSP (M): 502420. 502530. ⅜" BSP (M): 502530 TH. 502530 TH1. 502930 TH. Art. 502 Robocal Long: ⅜" BSP (M): 502630. 502630 CST. 502630 WLF. 502631 CST. 502635 CST. 502636 CST. 502638 CST. 502638 OEM. 502730. 502730 A. 502730 BSC. 502730 CST. 502730 GRN. 502730 NTR. 502822. ½" BSP (M): 502640. 502643A. 15mm compression: 502649. Art. 502 Minical ⅜": ⅜" BSP (M): 502030. 502030 CON. 502030 CST. 502031. 502034 CST. 502035 CST. 502036 CST. 502037 CST. 502037 VLL. 502037 WLF. 502038 CST. 502130. 502130 CST. 502130 ENC. 502130 FRT. 502130 GRN. 502130 TAK. 502130 TH. 502130 TH1. 502131. 502131 TH. 502132 DEC. 502133. 502134 DEC. 502135 RIF. 502231. 502231 CST. 502231 TH. 502232 TH. Art. 502 Minical ½" BSP (M): 502020 CST. 502040. 502040 CON. 502040 CST. 502040 MI. 502040A. 502041. 502041 MI. 502043. 502043 CST. 502043 IMM. 502043A. 502043A CST. 502046 IMM. 502140. 502140 ENC. 502140 FRT. 502141. 502142. 502144 ART. 502144 DEC. 502145 RIF. 502241. 502242 TH. 502243A. 502246 IMM. 502343A. ¾" BSP (M): 502050. 502051. 502052 CST. 1" BSP (M): 502060. 502061. Model added September 2021: ¾” BSP (F): 501500.
Product Images

Approval Holder:
Caleffi S.p.A
Company Name
Caleffi S.p.A
Address
Strada Regionale 229 n. 25 Fontaneto d'Agogna (NO)
Postcode
28010
Country
Italy
Phone
+39 0322 8491
General Email
gary.perry@caleffi.com

View All Listings by this Company
Manufacturer:
Caleffi S.p.A
Company Name
Caleffi S.p.A
Address
Strada Regionale 229 n. 25 Fontaneto d'Agogna (NO)
Postcode
28010
Country
Italy
Phone
+39 0322 8491
General Email
gary.perry@caleffi.com

View All Listings by this Company

Print This Approval


#2012363

Thermostatic mixing valve with a brass body within a plastic outer case. Flow is controlled via an electronically operated ceramic cartridge via a motor. Temperature is controlled via a temperature sensor that electronically adjusts the ceramic cartridge via a motor. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
2010 Shower Valves
Section Subtitle:
Shower valve(s) with thermostatic temperature control
WRAS Approval Number:
2012363
Note:
Claims of Hygienic properties are made by the manufacturer and not considered part of the listing.
Size:
M10 threaded inlets x ½” BSP (F) outlet
Marking:
Angel Guard logo and other technical information on adhesive label on body.
Installation Requirements:
R001 R010 R040
Expiry date:
31/12/2025
Model:
A121636 Angel Guard Hygienic mixing valve (HMV)

Approval Holder:
Angel Guard Limited
Company Name
Angel Guard Limited
Address
Lomond House 7 Greenbank Road Darvel Ayrshire
Postcode
KA17 0NN
Country
United Kingdom

View All Listings by this Company

Print This Approval


#2010096

Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members incorporates plastic aerators supplied with a pop-up waste. Maximum working Pressure 10.0 bar. Maximum operating temperature 65ºC.

Section:
0450 Combination Tap Assemblies
Section Subtitle:
Single hole tap(s) with a single outlet and a fixed spout.
WRAS Approval Number:
2010096
Note:
R160 applies to the waterfall outlets only.
Size:
Stainless Steel braided, PEX lined hose assembly incorporating ½” BSP captive nut end compression end connections.
Marking:
DTC53 (brand of Methven) on rear of body.
Installation Requirements:
R001 R006 R010 R160
Expiry date:
31/10/2025
Model:
SAVV2113UE COMBINATION TAP ASSEMBLIES

Approval Holder:
Methven UK Limited
Company Name
Methven UK Limited
Address
3-3A Stone Cross Court Yew Tree Way Golborne Warrington
Postcode
WA3 3JE
Country
United Kingdom
Phone
0800 195 1602
General Email
raluca.olariu@uk.methven.com

View All Listings by this Company

Print This Approval


#2010409

Aquaflow polypropylene bodied compression fittings with EPDM ‘O’-rings for use with Elysee PE80 blue pipes. The fittings are supplied with a pipe liner. Above and below ground use. Maximum working pressure 12.5 bar. Cold water use only.

Section:
1100 Fittings and Pipe - Compatible Systems
Section Subtitle:
Unless specified in the individual approval, the products within this section are not suitable for below ground use
WRAS Approval Number:
2010409
Note:
The liners supplied with each fitting must be used to maintain the validity of this approval. R008 applies to the connecting blue pipework when used above ground.
Size:
See model
Marking:
Fittings: AQUAFLOW, DVGW, EU, size and PN on the compression nut. Size and date of manufacture (clock format) on body. Pipe: AQUAFLOW, EN12201, size, PN and production date code (CDDMMY, where C = decade, and is replaced with 6 to indicate 2020).
Installation Requirements:
R001 R008
Expiry date:
31/10/2025
Model:
Aquaflow fittings & pipes for WRAS Approval AQUAFLOW COMPRESSION FITTINGS 20mm, 25mm, 32mm Male Adaptor 3200*****Q / Female Adaptor 320A*****Q / Male Elbow 322A*****Q / Female Elbow 322B*****Q / Wall Female Elbow 322D*****Q - The first *** denotes the 1st end diameter (016→16mm, 020→20mm etc). The last ** denotes the BSP thread (male or female) in inches (01→1/2”, 02→3/4”, 03→1” etc) Coupling 321******Q / Elbow 322******Q - The first *** denotes the 1st end diameter (016→16mm, 020→20mm etc). The last *** denotes the 2nd end diameter (016→16mm, 020→20mm etc). Reducing Coupling 321A*****Q - The first *** denotes the 1st end diameter (016→16mm, 020→20mm etc). The last ** denotes the 2nd end diameter (16→16mm, 20→20mm etc). Female Tee 3230*****Q / Male Tee 323A*****Q - The first *** denotes the 1st and 2nd end diameters (016→16mm, 020→20mm etc). The last ** denotes the BSP thread in the middle of the part (male or female) in inches (01→1/2”, 02→3/4”, 03→1” etc) End Plug 320B00***Q - The last *** denotes the nominal diameter (016→16mm, 020→20mm etc). Tee 324******Q - The first *** denotes the nominal diameter left and right (016→16mm, 020→20mm etc). The last *** denotes the nominal diameter of the middle connection (016→16mm, 020→20mm etc). Reducing Tee 324A*****Q - The first *** denotes the nominal diameter left and right (016→16mm, 020→20mm etc). The last ** denotes the nominal diameter of the middle connection (16→16mm, 20→20mm etc). Elbow Female For POP-UP 322C*****Q - The first *** denotes the 1st and 2nd end diameters (016→16mm, 020→20mm etc). The last ** denotes the BSP thread in the middle of the part in inches (01→1/2”, 02→3/4”) Repair Coupling 321B00***Q - The last *** denotes the nominal diameter of the connection (left and right the same) (016→16mm, 020→20mm etc). Universal Adaptor 321C*****Q - The first *** denotes the nominal diameter of the PE pipe connection (016→16mm, 020→20mm etc). The last ** denotes the nominal diameter of the alternative pipe material connection (15→15mm, 22→22mm, 28→28mm). Global Transition 321D0****Q- The first ** denotes the diameter of the alternative pipe material connection (22→22mm, 27→27mm, 34→34mm) . The last ** denotes the nominal diameter of the PE pipe connection (20→20mm, 25→25mm, 32→32mm). AQUAFLOW PE80 BLUE PIPES 20mm, 25mm, 32mm 21125020***Q - 20mmX2.3mm, SDR9, SF1.25, PN12.5 21125025***Q - 25mmX2.3mm, SDR11, SF1.25, PN12.5 21125032***Q - 32mmX3.0mm, SDR11, SF1.25, PN12.5 For the pipe codes, first two digits are the product code (same for all), next three digits state pressure rating (125 – PN12.5 bars), next three digits show external diameter of pipe (020 – 20mm) and last three digits are the length of the coil as customer prefers (025-25m, 050-50m, 100-100m)

Approval Holder:
Kalsi Plastics (UK) Limited
Company Name
Kalsi Plastics (UK) Limited
Address
Kalsi House 5 Tomey Road Sparkhill
Postcode
B11 2NJ
Country
Birmngham
General Email
george.argiropoulos@elysee.com.cy

View All Listings by this Company

Print This Approval


#2012555

'Balinit DLC-Star.' Factory applied, grey coloured CrN + a-C:H coating. Apply as per manufacturer's instructions reference 'VS200295' dated 18.03.2021. Cure for 6 hours@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:
5030 Coatings, Paints & Linings
Section Subtitle:
Factory applied pipe & fittings coatings.
WRAS Approval Number:
2012555
Expiry date:
31/12/2025

Approval Holder:
Oerlikon Balzers Coating Germany GmbH
Company Name
Oerlikon Balzers Coating Germany GmbH
Address
Am Ockenheimer Gragen 41, DE-55411 Bingen, Germany

View All Listings by this Company

Print This Approval


#2012094

Range of bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a plastic strainer. Maximum working pressure 10.0 Bar. Cold water use only.

Section:
2075 Float Operated Inlet Valve
Section Subtitle:
Can be used to achieve a recognised air gap arrangement, providing it meets the appropriate backflow requirements. Suitable for use in a WC suite, provided it forms an arrangement which meets the requirements of Type AUK1 air gap and an appropriate WC performance specification.
WRAS Approval Number:
2012094
Size:
½” BSP (M)
Marking:
Wirquin ON TOP OF VALVE WRAS, MODEL & BS1212-4 ON BODY
Installation Requirements:
R001 R550 R560
Expiry date:
31/12/2025
Model:
T6501 bottom entry
Product Images

Approval Holder:
Wirquin Ltd
Company Name
Wirquin Ltd
Address
Unit 3 Alpha Court Thorne Doncaster
Postcode
DN8 5TZ
Country
United Kingdom
Phone
01302 312252
General Email
mick.kirby@wirquin.co.uk

View All Listings by this Company

Print This Approval


#2012368

Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Models 91742, 95660 incorporate a non-rising spindle headwork with dome type operating members. Model 21775 incorporate a non-rising spindle headwork with cross top operating members. Model 77174 incorporate a quarter turn ceramic disc headwork with single lever operating members. The fitting incorporates a manual diverter to the shower outlet The spout outlet incorporates a plastic flow straightener and the products are supplied with a shower hose, shower handset and metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
0520 Combination Tap Assemblies
Section Subtitle:
Two hole tap(s) with a single outlet and a fixed spout, incorporating a manually operated diverter to a shower outlet.
WRAS Approval Number:
2012368
Size:
¾” BSP (M)
Marking:
ebb & flo on body
Installation Requirements:
R001 R020
Expiry date:
31/12/2025
Model:
91742, 21775, 95660 & 77174 combination tap assemblies
Product Images

Approval Holder:
Toolstation Ltd.
Company Name
Toolstation Ltd.
Address
Travis Perkins PLC Ryehill House Rye Hill Close Lodge Farm Industrial Estate Northampton
Country
United Kingdom
Phone
07392109053
General Email
benjamin.cockerill@travisperkins.co.uk

View All Listings by this Company

Print This Approval


#2012081

Range of normally closed and normally open plastic solenoid valves with EPDM ‘O’-rings and sealing rings. Pushfit connections for use with John Guest LLDPE pipe or copper pipe. The 47.004.103 model acts as a diverter between two outlets, where one outlet is always open. Maximum working pressures see model section. Maximum operating temperatures: 65°C - 47.00X.1XX models with John Guest LLDPE pipe only. 90°C - 47.004.103 model with John Guest LLDPE pipe only. Models added January 2021: Cold water use only - 47.00X.2XX (4mm & 8mm) with John Guest LLDPE pipe only. 90°C - 47.00X.2XX (6mm) with John Guest LLDPE pipe only. 90°C - 47.00X.2XX (6mm & 8mm) with copper pipe only.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2012081
Size:
See model.
Marking:
AUK Muller, technical information and date of manufacture (WWYY) on adhesive label on body.
Installation Requirements:
R001 R008
Expiry date:
31/12/2025
Model:
47.002.102 (NC - Normally Closed): 6mm pushfit - 8.0 bar. 47.002.102 (NC - Normally Closed): 8mm pushfit - 8.0 bar. 47.002.182 (NO - Normally Open): 8mm pushfit - 7.0 bar. 47.004.102 (NC - Normally Closed): 6mm pushfit - 3.5 bar. 47.004.102 (NC - Normally Closed): 8mm pushfit - 3.5 bar. 47.004.103 (NC - Normally Closed) 3/2 Way: Nozzle 7mm - 3.5 bar. Models added January 2021: 47.002.202 (NC - Normally Closed): 8mm pushfit - 8.0 bar. 47.003.202 (NC - Normally Closed): 8mm pushfit - 5.0 bar. 47.003.203 (NC - Normally Closed): 4mm pushfit - 5.0 bar. 47.003.203 (NC - Normally Closed): 6mm pushfit - 3.0 bar. 47.003.203 (NC - Normally Closed): 8mm pushfit - 3.0 bar. 47.004.202 (NC - Normally Closed): 6mm pushfit - 3.0 bar. 47.004.202 (NC - Normally Closed): 8mm pushfit - 3.5 bar. 47.004.282 (NO - Normally Open): 6mm pushfit - 3.0 bar. 47.004.203 (NC - Normally Closed): 6mm pushfit - 3.0 bar. 47.004.203 (NC - Normally Closed): 8mm pushfit - 3.0 bar.

Approval Holder:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company
Manufacturer:
A.u.K. Müller GmbH & Co. KG
Company Name
A.u.K. Müller GmbH & Co. KG
Address
Dresdener Str. 162, D-40595 Düsseldorf
Country
Germany
Phone
+49 211 7391 0
General Email
info@akmueller.de

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 232 of 350

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.