'Fluteck™P1000 & Fluteck™P1500'. White coloured, extruded, disc shaped PTFE components. For use with water up to 85°C.
'UPS SEAL-FLEX TAPE'. Extruded, self-fusing silicone rubber tapes available in Black and Red colours. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'F802'. White coloured, extruded PTFE material. For use with water to to 85°C.
'E9053AA 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 90. Tested in-radii sizes between 0.4mm and 3.65mm. For use with water up to 85°C.
'EP50/1 BLK'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 50. Tested in-radius 1.7mm. For use with water up to 85°C.
'CSTD/BS6920-BA60' (shore hardness 60), 'CSTD/BS6920-BA70' (shore hardness 70) and 'CSTD/BS6920-BA75' (shore hardness 75). Black coloured, compression moulded EPDM materials. Tested in-radius size 1.05mm. For use with water up to 85°C.
SI-55678 (shore hardness 50), SI-65678 (SH 60), SI-75678 (SH 70) & SI-85678 (SH 80) natural ‘O’ rings. SI-52109 (shore hardness 50), SI-62109 (SH 60), SI-72109(SH 70), SI-82109 (SH80) red coloured ‘O’ rings. SI-51501 (shore hardness 50), SI-61501 (SH 60), SI-71501(SH 70) & SI-81501(SH 80) blue coloured ‘O’ rings. Natural (appears white coloured), red or blue coloured, compression moulded silicone rubber ‘O’ rings. Shore hardness between 50 shore A and 80 shore A. Tested in-radii sizes between 0.5mm & 2.5mm. For use with water up to 85°C.
'Silicone-01 Heater Seal Ring'. White coloured, compression moulded Silicone ring. Shore hardness 70. Tested in-radius size 3.4mm. For use with water up to 85°C.
'Silicone-02 Sealing Gasket'. Natural (appears white), compression moulded Silicone gasket. Shore hardness 70. Tested in-radius size 1.25mm. For use with water up to 85°C.
'LOCTITE® 2700™'. Green coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet dated November 2024. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
Range of stop valves with plastic bodies. The valves incorporate a built in solenoid valve which is operated by a switch located on the valve or by a remote control. The leak detector supplied with model SVSM66MRD is not connected to any water pipe, is independent of the valve and is intended to be installed in the area at risk of leakage. It is intended to detect leakage and sends an electrical signal to close the valve. For use with copper pipe (manufactured to BS EN1057), PEX pipe (manufactured to BS7291-3) and PB pipe (manufactured to BS7291 -2). Maximum working pressure 10.0 bar. Cold water use only
'+GF+ PVC-C'. Grey coloured, injection moulded PVC-C fittings. For use with water up to 60°C.
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve activated via an infra-red sensor. The tap connects to the solenoid valve via a copper tail with a ½” BSP (F) captive nut and a fibre washer. The product is supplied with a combined TPE washer and stainless steel strainer to be installed on the inlet to the solenoid. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) electronically controlled tap assembly. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator, and products are supplied with interconnecting stainless steel braided silicone lined flexible hose assemblies. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Side and bottom entry BS1212 - 3 compact type float operated valve for WC flushing cisterns Maximum operating pressure 14 bar. Maximum operating temperature 23°C
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. For use with cold water only
The range of WC cisterns incorporating a BS 1212-4:2016 side entry or bottom entry float operated inlet valve providing a Type AG air gap arrangement and a flush outlet valve operated via a push button assembly for either full or reduced flush. Maximum operating pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. The supply hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. The supply hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of flow sensors with plastic bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
DC type pipe interrupter with a permanent atmospheric vent (DZR brass body) incorporating a flow regulator at the inlet and brass shroud. Maximum working pressure 6.0 bar. Cold water use only.
Spring loaded, resilient trim, in-line check valve cartridge with NBR & EPDM ‘O’-rings, plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 8.6 Bar. Maximum operating temperature 60°C.
Range of non-verifiable double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. The products incorporate a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Undercounter boiling water cistern with a stainless steel body, stainless steel element and silicone ‘O’-rings and gaskets. Maximum working pressure 8.0 bar. Maximum operating temperature 95°C.
Range of stainless steel calorifiers. Max working pressure 10 bar. Max operating temperature 90°C.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (chromium plated brass body) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of ½ turn ceramic disc headworks with plastic bodies (middle position off, quarter turn either way for hot or cold). For insertion into specifically dimensioned bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc and non-rising spindle headworks. Maximum working pressure 10.0 Bar Maximum operating temperature 85 °C.
Range of ceramic cartridge headworks with a plastic body. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85 °C.
Ceramic cartridge headwork with a plastic body. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VS11-BZ20 | ½” BSP | 10 bar | 85 °C | PPI 20 | Body | No | Non-rising spindle | Not Applicable | Not Applicable | ||
| VS11-BZ24 | ½” BSP | 10 bar | 85 °C | PPI 24 | Body | No | Non-rising spindle | Not Applicable | Not Applicable | ||
| VS5412-BZ20 | ½” BSP | 10 bar | 85 °C | PPI 20 | Body | No | Non-rising spindle | Not Applicable | Not Applicable | ||
| VS5412-BZ24 | ½” BSP | 10 bar | 85 °C | PPI 24 | Body | No | Non-rising spindle | Not Applicable | Not Applicable |
The difference between models are the splines only, one has 20 and the other has 24.
Single hole, single outlet, fixed, combination tap assembly (chromium plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. Model 24.341.xxx is supplied with lever operated pop up waste (not verified by test). Maximum working pressure 10 Bar. Maximum operating temperature 60°C.
Single hole, single outlet fixed combination tap assembly (chromium plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure - 5 Bar Maximum operating temperature - 60 °C
Range of single-hole, single outlet, (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Floor standing single hole, single outlet (fixed) combination tap assembly (chromium plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Model 33500671 is supplied with a lever type pop-up waste – not verified by test. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| CAP BASNW C | Chrome | 15mm compression | 5 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Flow Straightener | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193838 X XXX | VARIOUS | 1/2" BSP | 10 bar | 65 °C | PPI | Body | No | Ceramic cartridge | C Clamp | Aerator |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single-hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever type operating members. The spout outlet incorporates plastic flow straighteners. Products are supplied with click-type pop-up wastes (verified by test). Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SAI BAS C | Chrome | M10 X 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Aerator |
Page 209 of 222
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
