'Wudu brand-NF 131118'. Factory applied, black coloured, two-component, water based epoxy coating. Mix in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V2', dated '20240821'. Cure for 1 hour@50°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Dicoat 60 EX Blue'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's user instructions 'SPL/R&D/TTD/UI/007', version '01', dated '03.11.2022'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPONICS WP-NS (No. 20170209)'. Factory applied, dark grey coloured, two-component, solvent free epoxy resin coating consisting of a base and hardener. Mix base and hardener in a weight ratio of 7:3 and apply as per Product Data Sheet ‘1838-K’ dated February 2017. Cure for 168 hours@30°C, then 168 hours@60°C and 'rest' for 168 hours before use. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CP231200'. Factory applied, two-part water-based epoxy coating. Mix Parts A & B in a 5:1 weight ratio and apply as per manufacturer's instructions 'File No. HBB-01', 'Version: A', dated '2024.6.30'. Cure for 24 hours@26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001'. Factory applied, blue coloured epoxy coating. Apply as per manufacturers technical data sheet dated 9th November 2015. Cure for 2 minutes, 30 seconds@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'90000 KANEPOX SF-A'. Factory applied, two-part, cream or red coloured epoxy coatings consisting of component A and component B. Mix and apply as per data sheet ‘Rev. No. 01’ dated January 2024. Cure for 7 days@23°C. The cream coating is for use with water up to 50°C. Between February 2024 and August 2024, the red coating is for use with water up to 23°C. From September 2024 the red coating is for use with water up to 50°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'TOHPEPOWDER#6150 SHK GRAY QD'. Factory applied, grey coloured epoxy coating. Apply as per Tohpe Corporation instructions no '4230904550B'. dated 'Jan 28, 2025'. Cure for 5 minutes@200°C. For use with water up to 65°C.
'KLINGERSIL® C-4240'. Off-white coloured NBR/fibre gasket material manufactured by calendering. For use with water up to 85°C. For use only as a jointing/material having been tested at a reduced surface area to volume ratio. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation.
'KLINGERSIL® C-4430'. NBR/fibre gasket material, which is green coloured one side and white coloured the other, manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Busan-Tank'. Light grey coloured, hot pressed GRP panel. For use with water up to 50°C.
'Hylon N1040 H2 BK397 W & Hylon N1030 H2 BK397 W'. Black coloured, injection moulded, glass fibre filled polyamide materials. For use with water up to 60°C.
'LCPA-G(1)06 HMNC001'. Natural, (appears off-white), injection moulded, glass fibre filled nylon material. (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% (05) - 65%. For use with water up to 85°C.
'27GFT'. Natural (appears white), extruded PA66+30GF material. For use with water up to 85°C.
'Celanex 3300-2FC EF2001 natural'. Natural (appears cream coloured), injection moulded PBT material. For use with water up to 60°C.
'Tufcot T100'. Off-white coloured, polyester composite material manufactured by hand lay-up. For use with water up to 23°C.
'Ecoleader® EL-4300'. Dark Yellow coloured (transparent), Vinyl Ester Resin material manufactured by casting moulding process. For use with water up to 60°C.
'Ecoleader® EL-4060'. Yellow coloured (transparent), Unsaturated Polyester Resin material manufactured by casting moulding process. For use with water up to 50°C.
'Thermocomp JF006E-BK1B633'. Black coloured, injection moulded Polyethersulfone material. For use with water up to 85°C.
'Egelen PE100 & Egeplast 9010 pipes'. Egelen PE100 is a single layered, black coloured, extruded PE100 pipe. Egeplast 9010 is a dual layered, extruded PE100 pipe consisting of a black coloured inner layer and a blue coloured outer layer. For use with water up to 23°C.
'PE-B-01 Inlet Pipe'. Blue coloured, injection moulded Polyethylene pipe. For use with water up to 85°C.
'PE-R-02 Outlet Pipe'. Red coloured, injection moulded Polyethylene pipe. For use with water up to 85°C.
'PE-R-01 Thermocouple Protection Tube'. Red coloured, injection moulded Polyethylene tube. For use with water up to 85°C.
'Water Guide P96400-005'. Beige coloured (opaque), injection moulded PPO component. For use with water up to 65°C.
'NORYL™ 731S-701-01-01-00 black coloured, NORYL™ 731S-801-01-01-00 beige coloured, NORYL™ 731S-845-01-01-00 beige coloured & NORYL™ 731S-960-01-01-00 grey coloured'. Injection moulded PPE materials. For use with water up to 85°C
'SP Sereneplast'. Green coloured (with external red stripes), extruded PPR pipe. For use with water up to 60°C.
'SP Sereneplast Fittings'. Green coloured, injection moulded PPR fittings. For use with water up to 60°C.
'PP-01 Magnesium rod plastic joint'. White coloured, injection moulded Polypropylene Magnesium rod plastic joint. For use with water up to 85°C.
'Fluteck™P1000 & Fluteck™P1500'. White coloured, extruded, disc shaped PTFE components. For use with water up to 85°C.
'E9053AA 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 90. Tested in-radii sizes between 0.4mm and 3.65mm. For use with water up to 85°C.
'EPDM50P - ELAST45901, EPDM60P - ELAST46901, EPDM70P - ELAST47901 & EPDM80P - ELAST48901’. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.3mm. For use with water up to 85°C.
SI-55678 (shore hardness 50), SI-65678 (SH 60), SI-75678 (SH 70) & SI-85678 (SH 80) natural ‘O’ rings. SI-52109 (shore hardness 50), SI-62109 (SH 60), SI-72109(SH 70), SI-82109 (SH80) red coloured ‘O’ rings. SI-51501 (shore hardness 50), SI-61501 (SH 60), SI-71501(SH 70) & SI-81501(SH 80) blue coloured ‘O’ rings. Natural (appears white coloured), red or blue coloured, compression moulded silicone rubber ‘O’ rings. Shore hardness between 50 shore A and 80 shore A. Tested in-radii sizes between 0.5mm & 2.5mm. For use with water up to 85°C.
'Silicone-01 Heater Seal Ring'. White coloured, compression moulded Silicone ring. Shore hardness 70. Tested in-radius size 3.4mm. For use with water up to 85°C.
'Silicone-02 Sealing Gasket'. Natural (appears white), compression moulded Silicone gasket. Shore hardness 70. Tested in-radius size 1.25mm. For use with water up to 85°C.
'LOCTITE® 2700™'. Green coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet dated November 2024. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'+GF+ PVC-C'. Grey coloured, injection moulded PVC-C fittings. For use with water up to 60°C.
Side and bottom entry BS1212 - 3 compact type float operated valve for WC flushing cisterns Maximum operating pressure 14 bar. Maximum operating temperature 23°C
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. For use with cold water only
The range of WC cisterns incorporating a BS 1212-4:2016 side entry or bottom entry float operated inlet valve providing a Type AG air gap arrangement and a flush outlet valve operated via a push button assembly for either full or reduced flush. Maximum operating pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. The supply hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. The supply hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of flow sensors with plastic bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
DC type pipe interrupter with a permanent atmospheric vent (DZR brass body) incorporating a flow regulator at the inlet and brass shroud. Maximum working pressure 6.0 bar. Cold water use only.
Range of spring loaded, resilient trim check valve cartridges with plastic body. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Spring loaded, resilient trim, in-line check valve cartridge with NBR & EPDM ‘O’-rings, plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 8.6 Bar. Maximum operating temperature 60°C.
Range of non-verifiable double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. The products incorporate a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel calorifiers. Max working pressure 10 bar. Max operating temperature 90°C.
GRPBP range of one piece, pre-insulated cold water storage cisterns and covers for domestic water storage, supplied with a wholesome water kit. The cisterns walls are available in grey, blue, green, white, red and anthracite grey (external) colours and the cistern base is straw coloured. For cold water use only. From November 2024 the water contact layer of the cistern base and walls is available in grey or straw colours. The outer layer of the cistern base is available in blue, green, white, red and anthracite grey colours.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (chromium plated brass body) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 90°C.
Ceramic cartridge headwork with a plastic body and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar. Maximum operating temperature 80°C
Page 204 of 226
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
