UV disinfection unit with stainless steel body. Maximum working pressure 9.0 bar. Maximum operating temperature 55°C.
'Loctite PC 7255 GN (Green) coating for use with Bonderite M-NT 1455-W primer'. Factory applied, green coloured, two-component epoxy resin coating. In June 2025 ‘LOCTITE PC 7255 GY (Grey) coating for use with BONDERITE M-NT 1455 Primer-W Coating’ was added to the approval. Factory applied, grey coloured, two-component epoxy resin coating. Prime the surface to be coated with the Bonderite primer wipe. Mix and apply as per manufacturer’s TDS dated October 2016. Cure for 7 days@23°C at 45% relative humidity. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Balinit Milubia'. Factory applied, dark grey coloured, two layered coating system consisting of a titanium bottom layer & diamond like coating top layer. Apply as per manufacturer`s instructions '080224' dated 08-Feb-2024. No curing required. For use with water up to 85°C.
'Strongcoat EPW-P'. Site applied, two-component, light grey coloured (once applied) epoxy coating. Mix Part A (light grey coloured liquid) with Part B (orange coloured liquid) in a 8.1:3.78 volume ratio and apply coat 1 as per manufacturer's TDS 06-0020-A-2021. Cure for 24 hours@23°C. Mix and apply coat 2 in the same way as coat 1 and cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika MonoTop®-1010’, one-part cementitious bonding primer for use with ‘Sika MonoTop®-615’ one-part cementitious repair mortar. Mix ‘Sika MonoTop®-1010’ with tap water in the ratio of 25kg:5.25 litres. Apply as per manufacturer’s Product Data Sheet ‘020302020010000054, March 2021, Version 01.01’. Mix ‘Sika MonoTop®-615’ with tap water in the ratio of 25kg:3.8 litres and apply immediately to ‘Sika MonoTop®-1010’ as per manufacturer’s Product Data Sheet ‘020302040030000198, December 2021, Version 02.02’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vinoleo SS'. Colourless lubricant to be applied in accordance with manufacturer's TDS reference '163460 version 2'. For use with water up to 85°C.
Range of wedge shoes (part numbers 2005036, 2006536, 2008036, 2010036, 2012536, 2015036, 2020036, 2025036, 2030036, 2040036, 2650036, 2660036, 40005036, 40006536, 40008036, 40010036, 40015036, 40020036, 40025036, 2680036 & 126100036). Black coloured, injection moulded nylon wedge shoes. For use with water up to 50°C.
RIAMAXX HT 325 GF20 natur N88FWC. RIAMAXX HT 325 GF25 natur N88FWC. RIAMAXX HT 325 GF30 natur N88FWC. RIAMAXX HT 325 GF35 natur N88FWC. RIAMAXX HT 325 GF40 natur N88FWC. RIAMAXX HT 325 GF45 natur N88FWC. RIAMAXX HT 325 GF50 natur N88FWC. RIAMAXX HT 325 GF20 schwarz R88FWC. RIAMAXX HT 325 GF25 schwarz R88FWC. RIAMAXX HT 325 GF30 schwarz R88FWC. RIAMAXX HT 325 GF35 schwarz R88FWC. RIAMAXX HT 325 GF40 schwarz R88FWC. RIAMAXX HT 325 GF45 schwarz R88FWC. RIAMAXX HT 325 GF50 schwarz R88FWC. Natural (appears beige/brown) and black coloured, injection moulded, glass filled polyamide materials. For use with water up to 85°C.
'Ultradur® B4300 G6 FC Aqua Uncolored'. Uncoloured (appears cream), injection moulded PBT material. For use with water up to 85°C.
'Hyperzone HY4008'. Off-white coloured, compression moulded PE material. For use with water up to 23°C.
'Cool-FIT 4.0 & 2.0 Pipes'. Triple layered, extruded polyethylene pipe which comprises of a black coloured inner layer, off-white coloured insulation layer and black coloured outer layer. For use with water up to 65°C.
'Cool-FIT 4.0 & 2.0 Fittings'. Triple layered, injection moulded electrofusion fittings which comprise of black coloured inner layer, ivory coloured insulation layer and black coloured outer layer. For use with water up to 65°C.
`TORELINA A604WR G & TORELINA A604WR B'. Grey coloured and black coloured, injection moulded PPS materials (manufactured in Japan). For use with water up to 85°C.
‘TORELINA™ A604WR & TORELINA™ A604WR B’. Natural (appears beige) and black coloured, injection moulded PPS materials (manufactured in China). For use with water up to 85°C
‘ECOTEC tubsed® TS.50/TS.85'. Black coloured, extruded polypropylene water channel component. Shore hardness 74. For use with water up to 23°C.
'40-5048'. White coloured (translucent), injection moulded, polypropylene 'Filter Frame' component. For use with water up to 45°C.
‘GFPP-(1) SFKP (2)’. White coloured, injection moulded, glass fibre reinforced PP material. (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% - 50%. (2) is an internal code used to denote customer and is replaced with a 4 digit number between 0001 & 9999. For use with water up to 85°C.
'SP-402M'. Black coloured, compression moulded natural rubber material. Shore hardness 78. Tested in-radius size 1.0mm. For use with water up to 60°C.
'TJJH-EPDM gasket'. Black coloured, compression moulded EPDM gasket. Shore hardness 70. Tested in-radius size 1.2mm. Between April 2024 and March 2025, the gasket was for use with water up to 23°C. Between April 2025 and April 2029, the gasket is for use with water up to 65°C.
Initial approval was for ‘SMS-80’ (shore hardness 80) only. In April 2024 ‘SMS-50' (shore hardness 50) & ‘SMS-70’(shore hardness 70) were added to the approval. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
Page 204 of 311
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
