'XR0240012'. Black coloured, compression moulded EPDM material. Shore hardness 40. Tested in-radius size 1.5mm. For use with water up to 85°C.
'EPDM 69064340'. Black coloured, injection moulded EPDM sheet material. Shore hardness 57. Tested in-radius size 0.9mm. For use with water up to 23°C.
'XXE03'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.05mm. For use with water up to 85°C.
'RE EP/50, 'RE EP/60, 'RE EP/70 & RE EP/80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EP50'. Black coloured, compression moulded EPDM material. Shore hardness 50A. Tested in-radius size 0.97mm. For use with water up to 70°C.
'Seat Seal S1 & S2'. Black coloured (S2) or white coloured (S1), injection moulded silicone rubber components. Shore hardness 80. Tested in-radius size between 0.65mm & 1.54mm. For use with water up to 85°C.
'Brymec PVC Solvent Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'TDS Brymec CEMENT Rev 01' review date '27-05-2022'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Spears® FlameGuard® FS-5 One-Step'. Red/brown coloured, liquid solvent cement. Apply as per manufacturer's instructions 'FG-3-0321'. No cure required. For use with water up to 82°C.
'XFGJ-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X20220228F' dated '2022-2-28'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SPS-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'S20220601' dated '2022-6-1'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies (brass body in various finishes), incorporating a ceramic disc headwork with single lever operating member (model OMI-133 & IND-OMI133-XXX) OR ceramic cartridge headwork with a single lever operating members (all other models) and a lockable self-cancelling diverter to shower outlet. All models except OMI-133-C/P and IND-OMI133-XXX are supplied with an approved check valve cartridge at the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and the product is supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
'6083 black'. Black coloured, injection moulded CIIR rubber material. Shore hardness 50. Tested in-radius size 1.1mm. For use with water up to 70°C.
A range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Models A7552AA and A7553AA are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
A range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a single lever operating member. The spout outlet incorporates a plastic aerator. These products are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
A range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a single lever operating member. The spout outlet incorporates a plastic aerator. These products are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Single-hole, single outlet, swivel electronically controlled tap assembly with a brass body in various finishes (see model). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating member controlling both the flow and temperature. The spout outlet incorporates a pull-out spray with a plastic aerator. The inlets incorporate approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2), and a stainless-steel strainer Maximum working pressure 5 bar. Maximum working temperature 60°C.
Range of deck mounted sensor taps. The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (models 1070021 and 1070025). Maximum operating temperature 60°C (model 1070024).
Wall mounted infra-red single hole, single outlet electronically controlled combination tap assemblies with brass body (chrome plated), incorporating a solenoid valve controlling the flow. The spout outlets incorporate a plastic aerator.Stainless steel strainer on inlet Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (various finishes, see models). Flow is controlled by a solenoid valve activated via an infra-red sensor. The products incorporate a hand dryer feature that are activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products are supplied with a metal backnut. Maximum working pressure 8.0 bar. Cold water use only.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic flow straightener, and the inlet incorporates a plastic filter. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Page 198 of 554
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
