Range of spherical valves with various means of operation some via handle some with actuators, see models, comprising of a bronze valve body, spindle and ball valve, and EPDM O rings Maximum working pressure 16 bar Maximum operating temperature 90˚C.
Spherical valves incorporating a brass bodies and ball, PTFE seat, EPDM and NBR ‘O’-rings. The valve 8 718 657 822 incorporates a branch which is intended to connect to the primary circuit of a combination boiler. Maximum working pressure 10.0 Bar. Cold water use only.
Push fit in-line spherical valve with plastic body, for use with PE-X pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) and copper pipe (manufactured to BS EN1057). Maximum working pressure/temperature: 12.0 Bar (cold water) and 7.0 Bar at 65°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of bedpan washers and macerators with flow controlled by solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid cat 5). Maximum working pressure 6 Bar Maximum operating temperature 60°C
Range of floor standing or wall mounted water dispensers which dispenses ambient and/or chilled water. Flow is controlled via self-closing headwork and products have either tap with lever operating members, a tap with floor pedal (floor standing models only), a bubbler with push button or a bubbler with floor pedal (floor standing models only). Maximum working pressure 6.0 bar. Cold water use only.
'Iupital F10-02 nat, Iupital F20-03 nat & Iupital FG2025 nat (natural, appear white)'. 'Iupital F10-02 E9000 black & Iupital F20-03 E9001 black (black coloured)'. Injection moulded acetal materials. For use with water up to 85°C.
'Jotapipe IL6001 50S'. Factory applied, blue coloured, fusion bonded epoxy coating. Apply as per technical data sheet dated '10 September 2019'. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'9001 Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured epoxy coating. Apply as per manufacturer's TDS/IFU 'number: 001', 'First Edition', revision date 'March 20, 2025'. Cure for 60 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BSS-LM'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's User Instructions 'File no. BSS-LM-D0001', 'Date: 9.20.2025'. Cure for 10 minutes@190°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyglass VEF'. Factory applied, two-part, off-white coloured, vinyl ester coating. Mix parts A & B in a 98:2 mass ratio and apply as per manufacturer's instructions '2/23' last reviewed July 2020. Cure for 7 days@21°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 1331'. Grey coloured, site applied, two-component epoxy coating. First coat: Mix Belzona 1331 (white, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure for 6-8 hours@10°C or 3-4 hours@30°C then apply: Second coat: Mix Belzona 1331 (grey, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure in accordance with manufacturer’s IFU ’06-03-19’, ‘Completion of the Molecular Reaction’ table, ‘Full mechanical/thermal loading or water immersion’. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 5811DW2 (grey)'. Grey coloured, site applied, two-component epoxy coating. Mix Part A (grey, opaque glossy paste) with Part B (orange, transparent liquid) in a 4:1 mass ratio and apply as per manufacturer’s IFU ’16-03-19’. Cure for 4 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Grivory GVN-5H black 9915'. Black coloured, injection moulded PA 66 + PA 6I/X-GF50 material. For use with water up to 85°C.
'TECHNYL ® SAFE A 219WFC V30 BK’ (black coloured) & ‘TECHNYL ® SAFE A 219WFC V30 NC’ (natural, appears off-white). Injection moulded, glass fibre reinforced polyamide 6.6 materials. For use with water up to 85°C.
Grilamid LV-30H FWA natural. Grilamid LV-30H FWA black 9225. Grilamid LV-30H FWA grey 9497. Grilamid LV-43H FWA black 9225. Grilamid LV-50H FWA natural. Grilamid LV-50H FWA black 9225. Grilamid LV-65H FWA natural & Grilamid LV-65H FWA black 9225 were added to the approval in March 2026. Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. For use with water up to 85°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Grivory HT1V-3 FWA natural and black 9225. Grivory HT1V-4 FWA natural and black 9225. Grivory HT1V-4 FWA grey 9489. Grivory HT1V-4 FWA grey-blue 4637. Grivory HT1V-5 FWA natural and black 9225. Grivory HT1V-5 FWA grey L1366.3 & Grivory HT1V-5 FWA grey 9616. Grivory HT1V-5 FWA grey L16760.2. Grivory HT1V-6 FWA natural and black 9225. For use with water up to 85°C.
'Union Pipes Industry – K.S.A. HDPE Pipe' (made using BorSafe™ HE3490-LS, Hostalen CRP 100 Black, SABIC® HDPE P6006AD or TASNEE PE 100 black). Black coloured (with blue external stripes), extruded HDPE pipes. For use with water up to 60°C.
‘AQI380PRO’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’Load time’ cures set out in Table B4 of European Technical Assessment ETA 19/0127’, dated ‘28/02/2019’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’Load time’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 19/0127’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
Page 195 of 223
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
