Range of angled isolation valves (brass bodies – various finishes), incorporating a non-rising spindle headwork or quarter turn ceramic disc headwork with a dome or single lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Screw down stop valves. The 15BSC model has a DZR brass body and a T type operating member. The STAP200009 model has a chrome plated brass body and a dome type operating member. The 15BSC push fit connections are for use with copper pipe (manufactured to BS EN 1057), PB pipe (with inserts) (manufactured to BS EN 7291-2) and PEX pipe (with inserts) (manufactured to BS EN 7291-3). The STAP200009 model has compression connections which are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 12.0 bar. Cold water use only.
Thermostatic circulation valves incorporating DZR brass bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Thermostatic circulation valves incorporating DZR brass bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Thermostatic circulation valves incorporating DZR brass bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
‘Aquastrom’ range of regulating valves with brass bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 90.0°C
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 16.0 bar. Cold water use only.
Range of modular silver and copper disinfection ion generators with a stainless-steel bodies Maximum working pressure 9.0 bar. Cold water use only.
'Ronfalin ABS 609 White 2097P'. White coloured (opaque), injection moulded ABS materials. For use with water up to 85°C.
'CLEAN TECH PW (BG)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A and B in a volume ratio of 3:1 and apply as per manufacturer's TDS 'CCPL/TDS/R11/CRC/22-23/04/R13/BG/R1', dated '15.09.2022'. Cure for 7 days@30°C. Between August 2024 and January 2025, the coating is approved for use with water up to 23°C. Between February 2025 and August 2029, the coating is approved for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘NMSP2104 M & ER2104A01SM'. The following coatings were added to the approval in March 2025: ER2209A01SC, ER2252A01SC, ER2259A01SC & ER2260A01SC. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 38', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PMSP5099-M & EP5099D01SC'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 37', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PRIMGREEN® ENDURANCE & Primgreen LAT 12035' primers for use with 'RILSAN® PA11 T BLUE 7444 MAC (16293), PA11 T GREY 5161 MAC (17203), PA11 T WHITE 1488 AC (17219) & PA11 T BLACK 7450 AC (17185)' coatings. Factory applied primers and powder coatings. The piece to be coated is to be pre-heated to 330°C for 10 minutes, the primer and coating applied in accordance with user instructions 'Dircom - 4418E/05.2015/20' and then cured for 10 minutes@330°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SJ-195120WT GRP Panel'. Off-white coloured, compression moulded GRP panel. For use with water up to 50°C.
'Relon A500 Nero 4095 GF30 K'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 80°C.
'Pexylene 50937 Natural, Black & Blue'. Rotationally moulded polyethylene materials available in natural (appears off-white), black & blue colours. For use with water up to 65°C.
'BC245MO' & 'Bn BC245MO-90'. Natural (off-white), injection moulded polypropylene material. For use with water up to 85°C.
'Inoflon M 695'. White coloured (opaque), sintered PTFE material. For use with water up to 85°C.
'EP703904 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'EP703904 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'E13970'. Black coloured, injection moulded EPDM material. Shore hardness 65. Tested in-radius size 1.3mm. For use with water up to 23°C.
Page 155 of 214
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
