'Jain HDPE (PE 100) Blue Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
'Jain HDPE (PE 100) Black Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
‘Dowlex 2631UE & Dowlex 2631.10UE’ Natural (appear white coloured). ‘RX 102 Natural, RX 102 Black 9003 & RX 102 GR Black 9003’ (black coloured). In April 2025 ‘RX102 Blue 6263’ (blue coloured) was added to the approval. Rotationally moulded polyethylene materials. For use with water up to 70°C
‘Dowlex 2629UE & Dowlex 2629.10UE’. ‘RX 101 Natural, RX 101 Black 9003 & RX 101 GR Black 9003’. Natural (appears white coloured) and black coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Dowlex XZ89342.00 & Dowlex XZ89342.10’. ‘RX 137 Natural, RX 137GR black 9003 & RX 137 black 9003’. Natural (appears white coloured) and black coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Sabic R50035EE’. ‘RX 806 Natural, RX 806 Black 9003, RX 806GR Black 9003, RX 820 Light Blue 6001 & RX 820GR Light Blue 6001’. Natural (appears white coloured), black and light blue coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Tecotek OP20 GR10 NL 01 0A QF, Tecotek OP20 GR20 NL 01 0A QF & Tecotek OP20 GR30 NL 01 0A QF’. ‘Tecotek OP20 NL 01 0A QF’ was added to the approval in November 2023. Yellow/brown coloured, injection moulded, glass filled PPO/HIPS materials. For use with water up to 85°C.
‘4TECH 9S22110 W-A ANL, 4TECH 9S22120 W-A ANL & 4TECH 9S22130 W-A ANL’: Yellow/brown coloured, injection moulded, glass filled PPO/HIPS materials. For use with water up to 85°C.
‘Verplen C30 01 NE ACLKUV (black coloured), C30 04 NE ACLUV (black coloured), C30 08 NE ACLKUV (black coloured) & C30 08 NT ACLKUV (natural – appears beige coloured)’. Injection moulded, glass filled polypropylene materials. For use with water up to 60°C.
'ABR-PS'. Black coloured, injection moulded polystyrene material. Between July 2022 and 14th February 2023, the material is for use with water up to 23°C. From 15th February 2023 until July 2027, the material is for use with water up to 60°C.
'F801'. White coloured, extruded PTFE material. For use with water up to 85°C.
'F391'. Blue/grey coloured, extruded PTFE material. For use with water up to 85°C.
'F1500'. White coloured, extruded PTFE material. For use with water up to 85°C.
'INOLUB™ T201F, T202F, T203F, T204F & T205F'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
`Soltane F/B 197`. White coloured, extruded thermoplastic polyurethane material. For use with water up to 60°C.
'Dragon STD'. Site applied, off-white coloured, two-part epoxy resin and fibreglass cloth. Mix resin in a 77.8@22.2 volume ratio and apply to the fibreglass cloth. Once the cloth is fully impregnated, apply to the defect as per manufacturer's instructions 'IMG MPW 020' dated 01.07.2022. Cure for 24 hours@21°C or 4 hours@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'EP12/2/5 BLK 'O'-rings & seals'. Black coloured, injection moulded EPDM 'O' rings & seals. Shore hardness 50. The ‘O’ rings have a tested in-radius size of 1.0mm. The seals have a tested in-radius size of 0.75mm. For use with water up to 85°C.
‘4280’ black coloured injection moulded EPDM rubber components. Shore hardness 80. '4280 Membrane' has a tested in-radius size of 1.75mm. ‘4280 ’O’ rings’ have a tested in-radius size of 1.31mm. ‘4280 washers’ have a tested in-radius size of 1.05mm. All components are for use with water up to 85°C.
'GDE 7133', black coloured, compression moulded EPDM 'O' ring with a tested in-radius size of 2.0mm. In March 2025, ‘KD S-Ring’. black coloured, compression moulded EPDM seal with a tested in-radius size of 0.95mm was added to the approval. Both components have a shore hardness 70 and are for use with water up to 85°C.
'D0012'. Black coloured, EPDM rubber material manufactured by vulcanised moulding. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
Page 151 of 508
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
