Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of stop valves withbreonze, brass or chrome plated brass bodies, EPDM and PTFE washers incorporating a T type or lockshield operating members. To be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating pressure 85°C
Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Ultra-violet disinfection unit comprising of a stainless-steel body and quartz sleeve. Maximum working pressure 8.0 bar. Cold water use only.
'GCF-SRC'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a ratio of 4:2:1 and apply as per manufacturer's instructions 'QC-WI-8.1.8, revision 2/0, issue date 30/10/2021'. Cure for 28 days@24°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epoxy PB Pipe Green (W) & Epoxy FB Pipe Green (HW)'. Factory applied, green coloured epoxy powder coatings. The substrate to which the coating is to be applied is pre-heated to 220˚C for 15 minutes before applying the coating as per product data sheet dated '27th June 2023'. Post-cure for 15 minutes@215°C. For use with water up to 85°C. This material is only approved for the pre-heat and post-cure conditions that appear on the approval. If the pre-heat and/or post-cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HKUST002'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions 'HKUST002101001', '01', dated '03/11/2020'. Cure for 168 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Primer coating Spu‐221(A) & Spu‐221(B)’ for use with ‘Top coating: Spu‐222(A) & Spu‐222(B)’. Factory applied, grey coloured (once mixed) Acrylic Polyurethane primer & coating. Mix parts A and B of the primer in a 4:1 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. Mix parts A and B of the topcoat in a 4:2 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘FIBER TECH 82’. Factory applied, natural (appears dark yellow) fibreglass resin. Spray apply as per manufacturer’s Method Statement Ref ‘PP-GRP-092021-R1’, dated ‘21 Sept 2020’. Cure for 72 hours@25°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitocote EP405 (3821)’. Site applied, blue coloured, two component solvent free epoxy resin coating consisting of two bases (coat 1 base; Nitocote EP405 white & coat 2 base; Nitocote EP405 blue) & clear EP405 hardener. Mix parts A & B of each coat in a 100:13 weight ratio and apply in accordance with Fosroc data sheet issue 7 (CI/SfB: Pn6) dated November 2013. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MoyaProof WS2’. Site applied, grey coloured (once mixed), two-component, polymer modified Portland cement based cementitious waterproofing membrane. Mix Part A (white, opaque liquid) with Part B (grey, opaque powder) in a 1:4 mass ratio and apply two coats as per manufacturer’s Technical Datasheet ‘CC/MP05/Ver09/01/21’. Cure Coat 1 for 2 hours at 5˚C. Cure Coat 2 for 28 days at 5˚C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Renderoc Plug 20'. Site applied, dark grey coloured, cementitious repair mortar. Mix with water in a 3:1 volume ratio and apply as per manufacturer's datasheet '14' dated 'June 2018'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fusamatic Electrofusion Fittings'. Black coloured, injection moulded, polyethylene Electrofusion Fittings (made in UK from Ineos Eltex TUB121 & Hostalen CRP 100 Resist CR Black). In December 2023, Electrofusion Fittings made in Anhui Province China from Borouge Borsafe HE3490-LS & Hostalen CRP 100 Resist CR black were added to the approval. For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
'DIC.PPS FZ-2140-F3 BLACK'. 'DIC.PPS FZ-2140-F3 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials manufactured in Vienna, Austria. For use with water up to 85°C.
'Tefzel® ETFE 200, 207, 280, 750, HT2181, HT2183 & HT2185'. Un-pigmented (white coloured), compression moulded ETFE material. For use with water up to 85°C.
‘Sikadur 31 DW Rapid for use with Combiflex TF Tape’. Site applied, grey coloured two-component epoxy resin for use with grey coloured TPE Tape. Mix parts A & B of ‘Sikadur 31 DW Rapid’ in a 3:1 weight ratio and apply as per product data sheet ‘March 2021, Version 01.03’. Immediately apply ‘Combiflex TF Tape’ as per product data sheet ‘May 2021, Version 01.01’ and cure for 7 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikadur 31 DW for use with Combiflex TF Tape’. Site applied, grey coloured two-component epoxy resin for use with grey coloured TPE Tape. Mix parts A & B of ‘Sikadur 31 DW’ in a 3:1 weight ratio and apply as per product data sheet ‘February 2022, Version 03.03’. Immediately apply ‘Combiflex TF Tape’ as per product data sheet ‘May 2021, Version 01.01’ and cure for 7 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'212N' components. Black coloured, injection moulded EPDM rubber components with a shore hardness of 70. ‘O’ rings (in-radius 1.31mm), washers (in-radius 1.05mm) & membranes (in-radius 1.75mm) made in Italy. ‘O’ rings (in-radius 1.31mm) & washers (in-radius 1.05mm) made in China. For use with water up to 85°C. When processing an application for a Product Approval incorporating these components, these are the only shapes covered by the approval.
Page 140 of 176
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
