Range of screw down valves with brass bodies, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of screw down valves with brass bodies, , EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of magnetic, electrolytic or combined magnetic & electrolytic scale inhibitors with nickel plated copper bodies, for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 12.0 bar. Cold water use only.
‘FLOGUL® 656 Bleu 5005’. Factory applied, blue coloured VOC paint. Apply as per manufacturer’s TDS dated ‘06/04/2022’. Cure for 7 days@20°C. For use with water up to 60°C.
‘R-4401, E-44131, E-4413, E-4414, E-4420, E440001, E441001, E440002, E441002, E-5402, E-5403, E-5404, E540001. E541001, E540002, E540003, E541003 & E440007’. Factory applied, grey-blue coloured enamel coatings. Apply as per manufacturer’s instructions ‘issue 02/2016’ dated 05.10.2016. Cure for 6 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Apcoguard SF156'. Factory applied, grey coloured, two-component solvent-free epoxy coating. In January 2024, 'Apcoguard SF156', factory applied, red coloured, two-component solvent-free epoxy coating was added to the approval. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's Application Guidelines 'APPPG/SF156/001', dated 'Aug-2017'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempadur 35560 Light grey (10500), Light red (50900) & Cream (20320)'. Factory applied, grey, light red coloured & Cream, two-component epoxy coatings. Each colour can be used as a base or topcoat and as a two-coat system. Mix base and curing agent in a 6.8:2 volume ratio. Apply Light Grey and Light Red as per manufacturer's Application Instructions issued 'November 2019'. Apply Cream as per manufacturer's Product Data Sheet dated 'December 2023'. Cure Coat 1 for 16 hours@20°C. Cure Coat 2 for 7 days@20°C. Between December 2022 and November 2024, the Light Grey and Light Red were for use with water up to 40°C. Between December 2024 and December 2027, Light Grey and Light Red are for use with water up to 60°C. The Cream coating was added to the approval in May 2025 and is for use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Welmortar-III'. Factory applied, grey coloured cement mortar. Mix cement, sand and water in a mass ratio of 2:3:0.85. Apply as per manufacturer's Standard Operating Procedure 'WDIPL/QA/WI/14A', revision '0', dated '01.10.2021'. Cure for 21 days at 30°C & 70% humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Crystic VE660'. Olive coloured, contact moulded GRP material. For use with water up to 23°C.
‘ULTRAMID® A218W V30 Natural-C’ (natural, appears off-white) & ‘ULTRAMID® A218W V30 Black-C’ (black coloured). Injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Tecomid NA40 GR30 BK250 HS QW'. 'Tecomid NA40 GR35 BK250 HS QW'. 'Tecomid NA40 GR40 BK250 HS QW'. 'Tecomid NA40 GR45 BK250 HS QW'. 'Tecomid NA40 GR50 BK250 HS QW'. Black coloured, injection moulded, glass fibre reinforced (30% - 50%), PA66 materials. For use with water up to 85°C.
'Sierra PE-100 pipes'. Blue coloured, extruded PE-100 pipes. For use with water up to 65°C.
'Iglidur® UW160 Bearing'. Grey coloured, injection moulded PE bearing. For use with water up to 85°C.
'Kingbull PE100 Blue Fitting (391740)'. Blue coloured, injection moulded polyethylene fitting. 'Kingbull PE100 Black Fitting (0103208)'. Black coloured, injection moulded polyethylene fitting. Both for use with water up to 65°C.
'UGPM HDPE Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'P600 BL & P301E BL'. Black coloured, extruded polyethylene pipes. For use with water up to 23°C.
'S-Ion PE100 Fittings'. Blue coloured, injection moulded PE100 fittings. For use with water up to 65°C.
'Borsafe ME3440 (black), Borsafe ME3444 (blue) & Borsafe ME3440-W (black)'. PE80 materials suitable for injection moulding and extrusion purposes. For use with water up to 60°C.
'Thermocomp MB006SXP-BK1A994' (black coloured). Injection moulded polypropylene material. For use with water up to 85°C.
Page 125 of 442
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
