Range of gate valves with brass bodies, brass wedges and PTFE gaskets. The valves are operated via a non-rising spindle with a hand wheel operating member. The Z2020.028 compression model is for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of screw down stop valves incorporating brass or bronze bodies and EPDM gaskets. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of push-fit, screw down stop valves with plastic bodies for use with copper pipe (manufactured to EN1057), PEX pipe (manufactured to BS 7291-3) and/or MDPE pipe (manufactured to EN 12201 (inserts required). For above and below ground use. Maximum working pressure:16.0 bar Maximum operating temperature: 20.0°C.
'SF-CM1'. Factory applied, grey coloured, sulphate resistant cement mortar. Mix cement mortar, sand & water in a 2:1:0.4 mass ratio and apply as per manufacturer's user instructions 'SF-CM1', 'Vision A1' dated '2024-7'. Cure for 12 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Eurokote® 48-20 Brun Rouge’. Factory applied, red coloured, two-part epoxy coating. ‘Eurokote® 48-20 Ivoirine’ was added to the approval in March 2026. Factory applied, white coloured, two-part epoxy coating. Mix resin and hardener in a 2.13:1 mass ratio and apply as manufacturer's TDS dated '10/12/2024'. Cure for 24 hours@20°C. For use with water up to 23°C.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Blue Epoxy GPC)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a volume ratio of 3:1 and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/W1-16’, version ‘4.0’, effective date ’01.08.2025’. Cure for 12 hours @30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FGB15A -White, FGB15A -21364A Grey & FGB15A -21404A Grey'. ISOPOL modified, white or grey coloured brush Gelcoats. Apply as per manufacturer's TDS dated '04/11/2022'. Cure for 120 minutes@18°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tesnit BA-U Yellow & Blue'. Fibre/NBR materials, available in yellow or blue colours, manufactured by calendaring. Tesnit BA-U Blue is for use with water up to 85°C. Between September 2025 and February 2026, Tesnit BA-U Yellow was for use with water up to 23°C. Between March 2026 and September 2030, Tesnit BA-U Yellow is for use with water up to 85°C. Store and handle in accordance with 'STORING & HANDLING INSTRUCTIONS, dated November 12, 2025'. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Proofex HDPE B125'. White coloured, extruded HDPE waterproofing membrane. For use with water up to 60°C.
'Hepworth Qatar PPR 125 Pipe'. Green coloured (opaque), extruded PPR pipe. For use with water up to 85°C.
‘Udel P-3500 NT LCD, GF-110 NT, GF-120 NT, GF-121 NT, P-1700 NT 11 MR, P-1700 NT 11, GF-121 NT ECHO RP & P-3500 NT LCD ECHO RP’ (all beige translucent). ‘Udel P-1700 Grey 8057’ (grey coloured). ‘Udel P-1700 BK 937, P-1700 BK 937 MR, GF-120 BK 937, GF-121 BK 937, GF-121 BK 937 ECHO RP, GF-120 BK 937 ECHO RP & P-1700 BK937 ECHO RP’ (all black coloured). ‘Udel P-1700 WH 7407’ (white coloured). Injection moulded, polysulphone materials. For use with water up to 85°C.
'Tecoflex TU40 GR30 GR128 HS D6 QF'. Light grey coloured, injection moulded TPU material. For use with water up to 23°C.
‘AQI380PRO’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’Load time’ cures set out in Table B4 of European Technical Assessment ETA 19/0127’, dated ‘28/02/2019’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’Load time’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 19/0127’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure:8.0 Bar Maximum operating temperature:65 °C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of bottom and side entry BS1212-4 (2016) compact type float operated inlet valves, for WC flushing cisterns with plastic bodies and adjustable floats and a plastic flow regulator at the inlet. Maximum operating pressure: 10 bar. Maximum operating temperature: 23°C.
Concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
Page 106 of 124
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
