'GDPA PermaCoat'. Factory applied, blue coloured (once applied) coating system comprising of a Yellow Zinc Primer and Polyamide top coat. Apply one coat of Yellow Zinc as per work instructions 'PR/WI/01', revision '00', dated '22/11/2017', plating for 45 minutes@30°C. Apply one coat of top coat as per work instructions 'BR/WI/01', revision '00', dated '29/10/2010' and cure for 30 minutes@215°C. For use with water up to 23°C. This material is only approved for the plating and curing conditions that appear on the approval. If the plating and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BAJ0002'. Factory applied, blue coloured epoxy coating. Pre-heat substrate for 30 minutes@200°C and apply in accordance with manufacturer's Product Instructions 'Version-01 202426 September'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM1'. Factory applied, grey coloured cement mortar. Mix cement, sand, and water in a volume ratio of 1:2.0:0.4 and apply as per manufacturer's safety data sheet 'A1: 26-01-2020'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'LOCTITE® SF 770™' (known as 'LOCTITE 770'). Site applied, clear cyanoacrylate primer. Apply as per manufacturer's technical data sheet dated May 2021. Cure for 30 seconds@20°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RADILON® DT RV300RKC2 205 WT'. White coloured, injection moulded, glass filled Polyamide 612 material. For use with water up to 85°C.
‘TECHNYL ® SAFE D 219WFC V30 BK’ & ‘TECHNYL ® SAFE D 219WFC V50 BK’. Black coloured, injection moulded, glass fibre reinforced polyamide 6.10 materials. For use with water up to 85°C.
'Menzolit SMC1000 3018-White'. White coloured, hot-press compression moulded Polyester Sheet Moulding Compound (SMC). For use with water up to 30°C.
'ECOTRAN E2130W(#) NC'. Natural (appears beige) PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'ECOTRAN E2130W(#) BK'. Black coloured PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'RAMOFIN PPH301G6NT'. White/beige coloured, injection moulded polypropylene material. For use with water up to 85°C.
'TIMCO VESF 300/VESF 410'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 01.12.2025. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WEICONLOCK AN 306-20'. Green coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Griffon WDF-05®'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions '6306959 20251027'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Effast Tite'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions 'PLUMEFF', dated '2024/09/17'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVW105112111XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW103112111XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW125003001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW107008002XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW107008003XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVZ106003001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW111002001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVZ106010001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW112007001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW116001000XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator |
XX at the end indicates the Finish of surfaces that are not in contact with water (61 - Chrome, K5 - Matt black, 76 - Brushed gold, 64 - Brushed nickel).
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30 090 8xx | Various | G 1/2" | 10 bar | 65 °C | AXOR | on the nut | Yes | Not applicable | Not Applicable | Not Applicable | Shower Hose, |
Where 8xx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Range of shower kits with a shower hose, handset and shower rail. Open outlet use only Maximum operating temperature 60.0°C
Range of concealed, manually operated blending valves (brass bodies - various finishes), incorporating a ceramic cartridge headwork controlling the flow and temperature, a manually operated diverter to shower outlet with lever type operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TVS106353110xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS103353000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVT127001000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS112003000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS125003000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS104353000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS107005000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS106353113xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVT111001000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS122002000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS108008000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS105353110xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS00035100000 | null | 1/2" F | 10 bar | 60 °C | null | null | Yes | Ceramic cartridge | null | null | null |
TVS00035100000 – Vi-Box is used in conjunction with all of the models. Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
Range of ceramic cartridge headworks for insertion into specifically dimensioned tap assemblies. Maximum working pressure 12.0 bar Maximum operating temperature 85°C.
Page 105 of 113
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
