Standpipe assembly break tank with a Type ‘AB’ air gap (verified by test – suitable for backflow protection against fluid category 5) mounted to the top of the standpipe body. The tank is filled via a compact float valve and has two screened weir slots. Water is then supplied by gravity from the break tank to the hose outlet below. Flow is activated via a spherical valve located behind a lockable panel. In addition to the isolation valve, the product incorporates a single check valve assembly (suitable for backflow protection against Fluid Category 2) prior to the spherical valve and an in-line ‘Y’ pattern strainer after it. The spherical valve includes a drain plug to allow for draining. Insulation is provided up to the drain point. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line, non-verifiable single check valve assemblies consisting of a spring loaded, resilient trim, single check valve cartridge housed within a DZR brass body (brass or chrome plated). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Headwork assemblies (stainless steel or brass bodies) incorporating a quarter turn ceramic disc with single lever operating member. The outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Headwork assemblies (stainless steel or brass bodies) incorporating a quarter turn ceramic disc with single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. Each inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disk headwork with a single lever operating member. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The product is supplied with metal backnuts. UK-1DPXX models only are a single feed and come with an optional ½” NPSM (M) x ½” BSP (F) brass adapter. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. Each inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with plastic backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 36 110 000 model is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass or stainless steel body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The HV3 model is supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 65 °C.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Incorporating a ceramic cartridge headwork and single lever operating members however model 922034 is fitted with a non rising spindle headwork and dome type operating members. The spout outlet incorporates a plastic flow straightener on models: 922064, 922034, 922302, 922303, 922304 or flow straightener and aerator kit on models: 922311, 922312, 922313, and some models are supplied with a click waste. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes). Incorporating a ceramic cartridge headworks, and various operating members. The spout outlet incorporates a flow straightener and is also supplied with an optional aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating ceramic a cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, metal, single outlet (swivel) also with end swivel spout, combination tap assembly (brass or stainless steel body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, metal, single outlet (swivel) also with end swivel spout, combination tap assembly (brass or stainless steel body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, metal, single outlet (swivel) combination tap assemblies (brass body - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The VOLA KV6 and VOLA KV7 models also have an end swivel spout. The VOLA HV7 and VOLA KV7 models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass or stainless steel - INOX models), comprising of a concealed rough in set with a brass body and a variety of separate trim sets incorporating a ceramic cartridge headwork with a dome type or single lever operating member and a spout outlet. The spout outlet incorporates a plastic aerator. The products are supplied with click type (click clack) waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Page 1 of 124
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
