Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.

Non-metallic materials and components comply with BS6920 at 65°C

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2309367

Size:

See model.

Marking:

Lawton tubes logo, EN1254 and size on body.

Installation Requirements:

R001

Expiry date:

30/09/2028

Model:

JET BRAZING REDUCER 67X28 JET BRAZING REDUCER 67X35 JET BRAZING REDUCER 67X42 JET BRAZING REDUCER 67X54 JET BRAZING REDUCER 76X35 JET BRAZING REDUCER 76X42 JET BRAZING REDUCER 76X54 JET BRAZING REDUCER 76X67 JET BRAZING REDUCER 108X42 JET BRAZING REDUCER 108X54 JET BRAZING REDUCER 108X67 JET BRAZING REDUCER 108X76 JET BRAZING REDUCER 133X42 JET BRAZING REDUCER 133X54 JET BRAZING REDUCER 133X67 JET BRAZING REDUCER 133X76 JET BRAZING REDUCER 133X108 JET BRAZING REDUCER 159X54 JET BRAZING REDUCER 159X67 JET BRAZING REDUCER 159X76 JET BRAZING REDUCER 159X108 JET BRAZING REDUCER 159X133 JET BRAZING REDUCER 219X159 JET BRAZING STRAIGHT COUPLING 67 JET BRAZING STRAIGHT COUPLING 76 JET BRAZING STRAIGHT COUPLING 108 JET BRAZING STRAIGHT COUPLING 133 JET BRAZING STRAIGHT COUPLING 159 JET BRAZING STRAIGHT COUPLING      219 JET BRAZING REDUCED TEE 67X67X28 JET BRAZING REDUCED TEE 67X67X35 JET BRAZING REDUCEDTEE 67X67X42 JET BRAZING REDUCED TEE 67X67X54 JET BRAZING REDUCED TEE 76X76X28 JET BRAZING REDUCED TEE 76X76X35 JET BRAZING REDUCED TEE 76X76X42 JET BRAZING REDUCED TEE 76X76X54 JET BRAZING REDUCED TEE 108X108X35 JET BRAZING REDUCED TEE 108X108X54 JET BRAZING REDUCED TEE 108X108X76 JET BRAZING REDUCED TEE 133X133X54 JET BRAZING REDUCED TEE 133X133X108 JET BRAZING REDUCED TEE 159X159X54 JET BRAZING REDUCED TEE 159X159X133 JET BRAZING EQUAL TEE 67 JET BRAZING EQUAL TEE 76 JET BRAZING EQUAL TEE 108 JET BRAZING EQUAL TEE 133 JET BRAZING EQUAL TEE 159 JET BRAZING EQUAL TEE 219 JET BRAZING STOP END 67 JET BRAZING STOP END 76 JET BRAZING STOP END 108 JET BRAZING STOP END 133 JET BRAZING STOP END 159 JET BRAZING 90D ELBOW 67 JET BRAZING 90D ELBOW 76 JET BRAZING 90D ELBOW 108 JET BRAZING 90D ELBOW 133 JET BRAZING 90D ELBOW 159 JET BRAZING 90D ELBOW 219 JET BRAZING 45D ELBOW 67 JET BRAZING 45D ELBOW 76 JET BRAZING 45D ELBOW 108 JET BRAZING 45D ELBOW 133 JET BRAZING 45D ELBOW 159 JET BRAZING 45D ELBOW 219 JET BRAZING 45D STREET ELBOW 67 JET BRAZING 45D STREET ELBOW 76 JET BRAZING FEMALE IRON ADAPTOR 67X21.1/2 JET BRAZING FEMALE IRON ADAPTOR 76X3 JET BRAZING FEMALE IRON ADAPTOR 108X4 JET BRAZING MALE IRON ADAPTOR 67X2.1/2 JET BRAZING MALE IRON ADAPTOR 76X3 JET BRAZING MALE IRON ADAPTOR 108X4

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company

Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating ceramic disc headworks with single lever operating members (see models). The inlets incorporate stainless steel strainers. The spout outlets incorporate a plastic aerator or a flow straightener. Maximum working pressure 10 Bar. Maximum operating temperature 65 °C.

Section:

0470 Combination Tap Assemblies

Section Subtitle:

Single hole tap(s) with a single outlet and a swivel spout.

WRAS Approval Number:

2310379

Size:

Stainless steel braided EPDM lined hose assembly incorporating ½” BSP captive nut end connections

Marking:

Nabis on operating Member

Installation Requirements:

R001 R006 R010

Expiry date:

31/10/2028

Model:

B08926 * Idro Monoboloc Kitchen Tap

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company

Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1863 Tubes

Section Subtitle:

Elastomeric.

WRAS Approval Number:

2103346

Size:

DN 6 (denoted by 06) bore diameter availble with the following end connections: 01= F1/4 02= F1/4 elbow 03= M1/4 04= F3/8 05= F3/8 knurling nut 06= F3/8 insert without nut 07= F3/8 elbow 08= M3/8 09= F1/2 10= F1/2 wing nut 11= F1/2 elbow 12= M1/2 19= M8*(12-110) with single O-ring 20= M10*(12-110) with single O-ring; 21= M11*(12-110) with single O-ring 22= M12*(12-110) with single O-ring ; 23= M14*(12-110) with single O-ring 24= M15*(12-110) with single O-ring ; 26= F15 29=10mm Compression fitting 30=12mm compression fitting 31=15mm compression fitting 32=22mm compression fitting 33=15mm isolation valve 34=22mm isolation valve 35=10mm pushfit (used with copper tube manufactured to BS2871) 36=12mm pushfit (used with copper tube manufactured to BS2871) 37=15mm pushfit (used with copper tube manufactured to BS2871) 38=22mm pushfit (used with copper tube manufactured to BS2871) 39=10mm pushfit isolation valve (used with copper tube manufactured to BS2871) 40=12mm pushfit isolation valve (used with copper tube manufactured to BS2871) 41=15mm pushfit isolation valve (used with copper tube manufactured to BS2871) 42=22mm pushfit isolation valve (used with copper tube manufactured to BS2871) 45= M8*(12‐110) with double O‐ring 46= M10*(12‐110) with double O‐ring 47= M11*(12‐110) with double O‐ring 48= M12*(12‐110) with double O‐ring 49= M14*(12‐110) with double O‐ring 50= M15*(12‐110) with double O‐ring DN8 (denoted by 08) bore diameter availble with the following end connections: 03= M1/4 04= F3/8 05= F3/8 knurling nut 06= F3/8 insert without nut 07= F3/8 elbow 08= M3/8 09= F1/2 10= F1/2 wing nut 11= F1/2 elbow 12= M1/2 13= F3/4 14= F3/4 elbow 15= M3/419= M8*(12-110) with single O-ring 19= M8*(12-110) with single O-ring 20= M10*(12-110) with single O-ring; 21= M11*(12-110) with single O-ring 22= M12*(12-110) with single O-ring ; 23= M14*(12-110) with single O-ring 24= M15*(12-110) with single O-ring ; 25= M16*(12‐110) with single O‐ring 26= F15 27=15mm smooth tube 29=10mm Compression fitting 30=12mm compression fitting 31=15mm compression fitting 32=22mm compression fitting 33=15mm isolation valve 34=22mm isolation valve 35=10mm pushfit (used with copper tube manufactured to BS2871) 36=12mm pushfit (used with copper tube manufactured to BS2871) 37=15mm pushfit (used with copper tube manufactured to BS2871) 38=22mm pushfit (used with copper tube manufactured to BS2871) 39=10mm pushfit isolation valve (used with copper tube manufactured to BS2871) 40=12mm pushfit isolation valve (used with copper tube manufactured to BS2871) 41=15mm pushfit isolation valve (used with copper tube manufactured to BS2871) 42=22mm pushfit isolation valve (used with copper tube manufactured to BS2871) 43= F1/2 plastic nut 44= F3/4 plastic nut 45= M8*(12‐110) with double O‐ring 46= M10*(12‐110) with double O‐ring 47= M11*(12‐110) with double O‐ring 48= M12*(12‐110) with double O‐ring 49= M14*(12‐110) with double O‐ring 50= M15*(12‐110) with double O‐ring 51= M16*(12‐110) with double O‐ring DN10 (denoted by 10) bore diameter availble with the following end connections: 04= F3/8 05= F3/8 knurling nut 06= F3/8 insert without nut 07= F3/8 elbow 08= M3/8 09= F1/2 10= F1/2 wing nut 11= F1/2 elbow 12= M1/2 13= F3/4 14= F3/4 elbow 15= M3/419= M8*(12-110) with single O-ring 16= F1 17=F1 elbow 18= M1 20= M10*(12-110) with single O-ring; 21= M11*(12-110) with single O-ring 22= M12*(12-110) with single O-ring ; 23= M14*(12-110) with single O-ring 24= M15*(12-110) with single O-ring ; 25= M16*(12‐110) with single O‐ring 27=15mm smooth tube 28=22mm smooth tube 30=12mm compression fitting 31=15mm compression fitting 32=22mm compression fitting 33=15mm isolation valve 34=22mm isolation valve 35=10mm pushfit (used with copper tube manufactured to BS2871) 36=12mm pushfit (used with copper tube manufactured to BS2871) 37=15mm pushfit (used with copper tube manufactured to BS2871) 38=22mm pushfit (used with copper tube manufactured to BS2871) 39=10mm pushfit isolation valve (for use with copper tube) 40=12mm pushfit isolation valve (for use with copper tube) 41=15mm pushfit isolation valve (for use with copper tube) 42=22mm pushfit isolation valve (for use with copper tube) 43= F1/2 plastic nut 44= F3/4 plastic nut 46= M10*(12‐110) with double O‐ring 47= M11*(12‐110) with double O‐ring 48= M12*(12‐110) with double O‐ring 49= M14*(12‐110) with double O‐ring 50= M15*(12‐110) with double O‐ring 51= M16*(12‐110) with double O‐ring DN13 (denoted by 13) bore diameter availble with the following end connections: 04= F3/8 07= F3/8 elbow 08= M3/8 09= F1/2 10= F1/2 wing nut 11= F1/2 elbow 12= M1/2 13= F3/4 14= F3/4 elbow 15= M3/419= M8*(12-110) with single O-ring 16= F1 17=F1 elbow 18= M1 24= M15*(12-110) with single O-ring ; 25= M16*(12‐110) with single O‐ring 27=15mm smooth tube 28=22mm smooth tube 31=15mm compression fitting 32=22mm compression fitting 33=15mm isolation valve 34=22mm isolation valve 37=15mm pushfit (for use with copper tube) 38=22mm pushfit (for use with copper tube) 41=15mm pushfit isolation valve (for use with copper tube) 42=22mm pushfit isolation valve (for use with copper tube) 43= F1/2 plastic nut 44= F3/4 plastic nut 50= M15*(12‐110) with double O‐ring 51= M16*(12‐110) with double O‐ring DN19 (denoted by 09) bore diameter availble with the following end connections 13= F3/4 14= F3/4 elbow 15= M3/419= M8*(12-110) with single O-ring 16= F1 17=F1 elbow 18= M1 28=22mm smooth tube 32=22mm compression fitting 34=22mm isolation valve 38=22mm pushfit (used with copper tube manufactured to BS2871) 42=22mm pushfit isolation valve (used with copper tube manufactured to BS2871)

Marking:

MB (Brand of Navigator used under license by Wolseley), WRAS and year of manufacture (YYYY) on ferrule.

Installation Requirements:

R001

Expiry date:

31/03/2026

Model:

236550, 236548, 236543, 236547, 236551, 236545, 236549, 236542, 236541, 236544 & 236546

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company

Range of handwheel operated gate valves with brass bodies, gate & PTFE seals, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

2290 Valves

Section Subtitle:

Stop, gate, metal.

WRAS Approval Number:

2204717

Size:

see model

Marking:

MB (Brand of Navigator used under license by Wolseley), size & date of manufacturer M/M on body.

Installation Requirements:

R001

Expiry date:

30/04/2027

Model:

Gate valve light pattern C x C models: 236563 – CxC Brass Wheel Gate Valve – 15MM 236562 - CxC Brass Wheel Gate Valve – 22MM

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company

Range of quarter turn, lever handle operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

2204106

Size:

SEE MODELS

Marking:

MB (Brand of Navigator used under license by Wolseley), size, date of manufacture (MM/YY) on body. MB (Brand of Navigator used under license by Wolseley) ON/OFF, size and WRAS on lever.

Installation Requirements:

R001

Expiry date:

30/04/2027

Model:

Red/ Blue handle circlip reduced bore ball valve models: 236564 – CxC Brass Lever Ball Valve 15MM 236561 – CxC Brass Lever Ball Valve 22MM

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company

Range of manually operated dual flush WC outlet valves. Cold water use only.

Section:

1305 Flushing Mechanisms

Section Subtitle:

WC. Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

2310393

Size:

1 ½” BSP (M), 2” BSP (M).

Marking:

Wirquin moulded on body.

Installation Requirements:

R001 R571 R580 R581

Expiry date:

31/10/2028

Model:

B24004 NABIS manually operated dual flush WC outlet valves.

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company

Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.

Section:

0684 Combination Tap Assemblies

Section Subtitle:

Tap(s) with a non-touch methods of flow control and a single inlet.

WRAS Approval Number:

2312372

Size:

½” BSP (M)

Marking:

Saracen on body.

Installation Requirements:

R001 R006

Expiry date:

31/12/2028

Model:

C66102

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company

Range of single hole, single outlet, (swivel), combination tap assemblies (chromium plated brass bodies), incorporating quarter turn ceramic disc headworks and single lever operating members. The outlet is a pull down spray type and incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C

Section:

0445 Combination Tap Assemblies

Section Subtitle:

Tap(s) incorporating a pull-out/pull down spray where the airgap cannot be maintained after motive force is removed.

WRAS Approval Number:

2311369

Size:

Stainless steel braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections. 15mm compression – (137040 models only)

Marking:

Nabis on operating member.

Installation Requirements:

R001 R006 R010

Expiry date:

30/11/2028

Model:

B08929* Vico mono pull out kitchen tap

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company

Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass body), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporate a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65˚C.

Section:

0470 Combination Tap Assemblies

Section Subtitle:

Single hole tap(s) with a single outlet and a swivel spout.

WRAS Approval Number:

2402806

Size:

Stainless steel braided EPDM/PEX lined flexible hose assemblies incorporating ½” BSP captive nut end connections.

Marking:

Nabis on tap Body

Installation Requirements:

R001 R006 R010

Expiry date:

28/02/2029

Model:

B08915* Matese monobloc kitchen tap

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company

Range of wall mounted, thermostatic bar shower mixer (chrome plated brass body), incorporating a quarter turn ceramic disc headwork that controls the flow with a dome operating member. Temperature is controlled independently via a thermostatic cartridge with dome type operating member that incorporates a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. This product is supplied with an overhead shower, handset, shower hose and a riser rail assembly that incorporates a manual diverter that controls flow from overhead shower and shower handset. Maximum working pressure 5.0 bar

Non-metallic materials and components comply with BS6920 at 60°C

Section:

2010 Shower Valves

Section Subtitle:

Shower valve(s) with thermostatic temperature control

WRAS Approval Number:

2311920

Size:

15mm Compression

Marking:

Nabis on body.

Installation Requirements:

R001 R010 R040

Expiry date:

30/11/2028

Model:

A05033* NAB DISC ERD BAR Thermostatic Shower Valves

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company