'PAKMEL EP#3500 Series'. Factory applied, grey coloured epoxy coating. Apply as per manufacturer's instructions dated 2020.11.27. Cure for 3 minutes@230°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Sagar Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Krystaline Add1'. Site applied, white coloured (opaque) waterproofing admixture in the form of a powder. Admixture to be added to cement in a dosing ratio of 1kg/m³. Wet cure for 48 hours@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TECSIT K1'. Site applied, white coloured (opaque) waterproofing admixture in the form of a powder. Admixture to be added to cement in a dosing ratio of 1kg/m³. Wet cure for 48 hours@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Novus N49 Graftec`. NBR/fibre material which is dark grey on one side and black on the other. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'FTC GRP Panel'. Grey (opaque) coloured, compression moulded GRP panel. For use with water up to 50°C.
'GRP-FPI-KSA Fiberstrong'. Pale green coloured (opaque) GRP pipe manufactured by filament winding. Between September 2020 and April 2024 the pipe was for use with water up to 50°C. From May 2024, the pipe is for use with water up to 60°C.
'SH Special Seal grease'. Opaque, white coloured silicone grease. Apply as per manufacturer's instructions. No cure required. For use with water up to 65°C.
'Greasil 4000'. White coloured silicone grease. For use with water up to 85°C.
Page 10 of 112
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
