'Chang QI/CFPC'. White coloured PTFE tape manufactured by press strip roller. For use with water up to 60°C.
'(UREFLEX) TM390'. Off-white coloured, injection moulded PUR material manufactured by casting. For use with water up to 23°C.
'Intercrete 4800'. Site applied, grey coloured cementitious repair mortar. Mix Intercrete 4800 and water in a mass ratio of 7.58:1. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Chemfix 10'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 600'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '11/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`1025 Titan Bladder`. Black coloured, calendared butyl rubber sheet material. Shore hardness 60. Tested in-radius size 0.5mm. For use with water up to 23°C.
'ERIKS 55985 Gaskets & ‘O’ rings'. Black coloured, compression moulded EPDM gaskets & ‘O’ rings'. Shore hardness 70A. The gaskets have a tested in-radius size of 1.0mm. The ‘O’ rings have a tested in-radius size of 1.76mm. For use with water up to 85°C.
'LOPI60 & LOPI70'. Black coloured, injection moulded, EPDM 'O' rings. Shore hardness 60 & 70 respectively. Tested in-radius size 0.75mm. For use with water up to 85°C.
'LOPI60 & LOPI70'. Black coloured, injection moulded, EPDM 'O' rings. Shore hardness 60 & 70 respectively. Tested in-radius size 0.75mm. For use with water up to 85°C.
`RG EP W80`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'SEAEP80N01'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80A. Tested in-radius size 1.55mm. For use with water up to 85°C.
'E8121'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80A. Tested in-radius size 1.55mm. For use with water up to 85°C.
'RVK EPDM EP 210107'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'TYT_001'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 0.5mm. For use with water up to 23°C.
'TWK4563'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 0.5mm. For use with water up to 23°C.
'E0265'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. Between September 2021 and 3rd August 2022, the material was for use with water up to 23°C. Between 4th August 2022 and September 2026, the material is for use with water up to 50°C
'S-9028'. Black coloured, compression moulded EPDM rubber material Shore hardness 60 ShA. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EBW-65'. Black coloured, compression moulded EPDM rubber material. Shore hardness 65. Tested in-radius size 0.98mm. For use with water up to 85°C.
'7400 D-ring gasket'. Red/brown coloured, compression moulded, silicone rubber D-ring gasket. Shore hardness 45. Tested in-radius size 0.70mm. For use with water up to 23°C.
'OLDAL VMQ880 65TR – VMQ4303'. Colourless (translucent), extruded VMQ rubber material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
Page 88 of 582
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
