Range of floor-standing gas combination boilers, supplied with isolation valves, expansion vessel and a pressure relief valve set at 3.0 bar. Maximum working pressure: Primary circuit 2.5 bar, secondary 10 bar. Maximum operating temperature: Primary 82°C / secondary circuit 60°C.

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

250904711

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

22mm compression.

Marking:

Worcester on front cover. Worcester and product info on label inside cover.

Installation Requirements:

R001 R140 R360

Expiry date:

30/09/2030

Model:

7-731-600-297 Greenstar 8000F 35kW Combi NG, 7-731-600-298 Greenstar 8000F 35kW Combi LPG, 7-731-600-299 Greenstar 8000F 50kW Combi NG, 7-731-600-300 Greenstar 8000F 50kW Combi LPG.

Approval Holder:

Bosch Thermotechnology Ltd.

Company Name

Bosch Thermotechnology Ltd.

Address

Danesmoor Works Pilsley Clay Cross Chesterfield Derbyshire

Postcode

S45 9BY

View All Listings by this Company

Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M) or 1” BSP (M)

Marking:

APATOR, date of manufacture (YYYY) and product information on face of water meter. Flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

Maximum operating temperature 50°C: JS 1,6-02 JS 1,6-04 JS 1,6-NK JS 1,6-NKP JS 4-02 JS 4-04 JS 4-NK JS 4-NKP JS 2,5-02 JS 2,5-04 JS 2,5-NK JS 2,5-NKP JS 2,5-G1-02 JS 2,5-G1-04 JS 2,5-G1-NK JS 2,5-G1-NKP Maximum operating temperature 85°C: JS90 1,6-02 JS90 1,6-04 JS90 1,6-NK JS901,6-NKP JS90 2,5-02 JS90 2,5-04 JS90 2,5-NK JS90 2,5-NKP JS90 2,5-G1-02 JS90 2,5-G1-04 JS90 2,5-G1-NK JS90 2,5-G1-NKP JS90 4-02 JS90 4-04 JS90 4-NK JS90 4-NKP

Approval Holder:

Pittway Sarl

Company Name

Pittway Sarl

Address

A3 - ZA La Pièce 6 1180 Rolle

Country

Switzerland

View All Listings by this Company

Manufacturer:

Apator Powogaz S.A.

Company Name

Apator Powogaz S.A.

Address

Jaryszki 1C, 62-023 Żerniki

Country

Poland

Phone

+48 789 454 593

View All Listings by this Company

An in-line ultra-sonic water meter with brass (WM15) or plastic (SM15) bodies. Maximum working pressure: 16 Bar. Maximum operating temperature: 50°C (WM15) or 70°C (SM15).

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M).

Marking:

Sagemcom, CE, DN, max temperature and other technical information on meter face. Flow arrow on body

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

WM15: available in 110mm, 115mm, 165mm lengths. SM15: available in 110mm length.

Approval Holder:

Sagemcom Energy & Telecom

Company Name

Sagemcom Energy & Telecom

View All Listings by this Company

Range of water meters with plastic bodies and plastic turbines. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

SJ-SDC plus.

Marking:

NWM, NWM logo, and tech info on dial face. Flow arrow and DN on valve body. NWM & NWM logo on cover.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

½” BSP (M) inlet / ½” BSP (M)outlet (DN15), ¾” BSP (M) inlet / ¾” BSP (M)outlet (DN20), ½” NPT (M) inlet / ½” NPT (M) outlet (DN15), ¾” NPT (M) inlet / ¾” NPT (M) outlet (DN20).

Approval Holder:

Ningbo Water Meter (Group) Co., Ltd

Company Name

Ningbo Water Meter (Group) Co., Ltd

Address

No 355 Hongxing Road Jiangbei District Ningbo

Country

China

View All Listings by this Company

Range of flow sensors incorporating either brass, plastic or stainless steel bodies & EPDM ‘O’-rings. Maximum working pressure 10.0 bar for models VVXA, VVXC, VVXB. Maximum working pressure 16.0 bar for models VVXD & VVXE. Maximum operating temperature 90°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Sika logo, pressure, temperature, other tech info on body; flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

VVXA Vortex Flow Sensor Type VVX15 Vortex Flow Sensor nominal size 15. Body material PPS, G ¾ male or ½” NPT male VVXC Vortex Flow Sensor Type VVX20 Vortex Flow Sensor nominal size 20. Body material PPS G 1 male or ¾” NPT male or Quick-Fasten male/female VVXB Vortex Flow Sensor Type VVX25 Vortex Flow Sensor nominal size 25. Body material PPS G 1¼ male or 1” NPT male VVXD Vortex Flow Sensor Type VVX32 Vortex Flow Sensor nominal size 32. Body material brass or stainless steel G 1½ male or 1½” NPT male VVXE Vortex Flow Sensor Type VVX40 Vortex Flow Sensor nominal size 40. Body material brass or stainless steel G 2 male or 2” NPT male • digit 1,2,3: Designation of the series o VVX >>> VVX series • digit 4: nominal diameter o A >>> DN 15 for type VVX15 o C >>> DN 20 for type VVX20 o B >>> DN 25 for type VVX25 o D >>> DN 32 for type VVX32 o E >>> DN 40 for type VVX40 • digit 5,7,8,9,10,11,12,13,14,15: Device configuration • digit 6: Private label o S >>> SIKA (standard) o E >>> SIKA (standard) with ETL marking • digit 4 and 16: tube material / process connection o A and 4 >>> PPS – G 3/4 male thread o A and C >>> PPS – ½”NPT male thread o C and P >>> PPS – Quick-Fasten connection o C and 7 >>> PPS – G 1 male thread o C and 8 >>> PPS – 3/4" NPT male thread o B and 6 >>> PPS – G 1 1/4 male thread o B and E >>> PPS – 1” NPT male thread o D and U >>> Brass – G 1 1/2 male thread o D and 0 >>> Brass – 1½" NPT male thread o D and M >>> Stainless steel – G 1 1/2 male thread o D and Y >>> Stainless steel – 1½" NPT male thread o E and X >>> Brass – G 2 male thread o E and 9 >>> Brass – 2" NPT male thread o E and O >>> Stainless steel – G 2 male thread o E and Z >>> Stainless steel – 2" NPT male thread

Approval Holder:

SIKA Systemtechnik GmbH

Company Name

SIKA Systemtechnik GmbH

Address

Struthweg 7-9 Kaufungen

Postcode

34260

Country

Germany

Phone

+49 5605 803 652

General Email

grass@sika.net

View All Listings by this Company

Range of booster pumps with stainless steel bodies, plastic impellers, and NBR ‘O’-rings. The products incorporate a temperature sensor, pressure sensor, pressure vessel and a non-return valve integral to the pump chamber. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2204372

Size:

1” BSP (F)

Marking:

SFA Logo, Saniboost Smart, model number other technical information on adhesive label on body.

Installation Requirements:

R001 R415

Expiry date:

30/04/2027

Model:

Saniboost Smart Intelligent Water Booster Pump.

Approval Holder:

SFA Saniflo UK Ltd

Company Name

SFA Saniflo UK Ltd

Address

Unit 1 Watford Interchange Colonial Way Watford

Postcode

WD24 4WP

Country

United Kingdom

Phone

020 8842 0033

General Email

Graham.davies@sfasaniflo.co.uk

View All Listings by this Company

Range of multistage centrifugal pumps with stainless-steel housings, stainless-steel impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250902720

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN25 - DN200 flanged.

Marking:

Dooch, model, serial number and technical info on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

30/09/2030

Proviso:

The discharge from the drain core must be made via a type AA, AB or AD air gap, or in accordance with EN 1717.

Model:

XRLNa-b-c-d Where: XRL = model. With N = Wetted metallic material in SUS316L, Without N = Wetted metallic material in SUS304. a = Rated flow in m³/h (1 – 255). DN25 = 1-3. DN32 = 4-5. DN40 = 10. DN50 = 15-20. DN65 = 32. DN80 = 45. DN100 = 64 or 95. DN150 = 125-155. DN200 = 185-255. b = Number of impellers (stages 1 – 36). DN25 & DN32 models with 1 – 36 stages. DN40 models with 1 – 22 stages. DN50 models with 1 – 17 stages. DN65 models with 1 – 14 stages. DN80 models with 1 – 13 stages. DN100 models with 1 – 8 stages. DN150 models with 1 – 10 stages. DN200 models with 1 – 8 stages. c = Number of cutting impellers (0 – 3). (Note: c can be omitted when c = 0.) d = DN size (DN25 – DN200). (Note: d can be omitted.) E.g., XRL32-7-2-DN65 denotes: Pump is made of SUS304, rated flow 32 m³/h, 7 impellers, 2 cutting impellers and size DN65.

Approval Holder:

SHANGHAI SINO-KOREA DOOCH PUMP MFG. CO., LTD

Company Name

SHANGHAI SINO-KOREA DOOCH PUMP MFG. CO., LTD

Address

No 239 Zhangliantang Rd Liantang Ind Park Qingpu District Shanghai City China

View All Listings by this Company

Manufacturer:

ZHONGHAN DOOCH PUMP(HUZHOU)CO., LTD.

Company Name

ZHONGHAN DOOCH PUMP(HUZHOU)CO., LTD.

Address

NO 669 DAYANG ROAD KANGSHAN STREET HUZHOU ZHEJAING CHINA

View All Listings by this Company

Range of pumps, with stainless steel bodies, impellers and shaft. Maximum working pressure 10.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250904702

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Wilo, made in Korea, Model No., Serial No., website address, & other tech info on data label. Wilo printed on control panel.

Installation Requirements:

R001 R415

Expiry date:

30/09/2030

Model:

PBI-L203EA - Suction 25A(1”) Discharge 25A(1”) PBI-L204EA - Suction 25A(1”) Discharge 25A(1”) PBI-L205EA - Suction 25A(1”) Discharge 25A(1”) PBI-L402EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L403EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L404EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L405EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L802EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-L803EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-LD203EA - Suction 25A(1”) Discharge 25A(1”) PBI-LD402EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD403EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD404EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD405EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD802EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-LD803EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) 1 - Series PBI-L: Electronic Boosting Pump Variable Speed Pump(Inverter Pump). 2 - Number of Pumps None/blank : Single Type (One Pump), D: Duplex Type (Two Pumps). 3 - Rated Flow capacity 2 : 2㎥/hr, 4 : 4㎥/hr, 8 : 8㎥/hr. 4 - Number of Impellers 02 : 2 Impellers, 03 : 3 Impellers, 04 : 4 Impellers, 05 : 5 Impellers. 5 - Power 60Hz L: 110V ~, J: 120V ~ , 127V~, M: 220V~ D: 110V/220V~, I: 220/380V 3~, T: 220V 3~, U: 380V 3~, N: 440V 3~, R: 480V 3~. 50Hz Z: 110V ~, C: 120V ~, 127V~, E: 220V ~, F: 110V/220V ~, G: 220/380V 3~, H: 220V 3~, Q: 380V 3~, Y: 440V 3~. 6 - Automatic mode. None/blank : non automatic models A: models which equips themselves with components that are responsible for automatic mode.

Approval Holder:

WILO Pumps Ltd.

Company Name

WILO Pumps Ltd.

Address

46, Mieumsandan 1-ro, Gangseo-gu, Busan, Republic of Korea, 46730

View All Listings by this Company

Wall mounted finish set incorporating a dome type operating member and a shower hose and handset (chromium plated brass). Outlet to shower incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only. Maximum operating temperature 60°C

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

250402068

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M)

Marking:

AXOR on hand shower and shower hose ferrule.

Installation Requirements:

R001 R040

Expiry date:

30/04/2030

Model:

10 651 xx0. Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Range of shower outlets with brass bodies (various finishes) and NBR ‘O’-rings. Maximum working pressure 5.0 bar.

Non-metallic materials and components comply with BS6920 at 65°C

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

2301378

Size:

15mm compression

Marking:

Bagnodesign on handset & faceplate.

Installation Requirements:

R001 R040

Expiry date:

31/01/2028

Model:

BDP-OUT-R602-XX ROUND WALL OUTLET WITH BRACKET BDD-HSW-535-A-XX & BDD-HSW-535-XX HAND SHOWERS XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C) & Truffle (TF-C)

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company