‘Tecotek OP20 BK014 01 0A QF, Tecotek OP20 GR30 BK014 01 0A QF, Tecotek OP20 GR10 BK014 01 0A QF & Tecotek OP20 GR20 BK014 01 0A QF’. Tecotek OP20 BK014 01 0A QF is a black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C. Tecotek OP20 GR30 BK014 01 0A QF, Tecotek OP20 GR10 BK014 01 0A QF & Tecotek OP20 GR20 BK014 01 0A QF are black coloured, injection moulded, filled PPO/HIPS materials suitable for use with water up to 85°C.
‘4TECH 9S20000 W-A-ABK 01 0A QF, 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK’. Black coloured, injection moulded PPO & PPO/HIPS materials. 4TECH 9S20000 W-A-ABK 01 0A QF is an unfilled PPO material suitable for use with water up to 23°C. 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK are filled PPO/HIPS materials suitable for use with water up to 85°C.
'J-FIX ULTRA-BOND 100 EPOXY RESIN'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions 'Re00', dated 'August 2023'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPDM 5070 Membrane'. Black coloured, compression moulded EPDM membrane. Shore hardness 58. Tested in-radius size 1.02mm. For use with water up to 85°C.
'EP703901 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. For use with water up to 85°C.
'EP210107'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EPDM-A-001'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'TT-001 Natural'. Natural (appears white, translucent), compression moulded silicone rubber material. Shore hardness 50. Tested in-radius size 0.5mm. For use with water up to 85°C.
'Superpower SOS 3 in 1 (SP2)'. Green coloured (translucent) anaerobic adhesive. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
‘THERMOLAST DW’ range of natural (appears off-white), black, white & grey coloured, extruded TPE-S materials with an in-radius between 0.39mm & 0.41mm. DW7HTV-(1) (70 ShA). DW7HTU-(1) (75 ShA). DW8HTV-(1) (80 ShA). DW8HTU-(1) (85 ShA). DW9HTV-(1) (90 ShA). DW0HTV-(1) (40 ShD). (1) – indicates the colour of the material: - LCNT: means without pigment (natural colour). - 9017: means black coloured material. - 9003: means white coloured material. - 7---: 4 digit code means grey coloured material, mixture of white and black pigments. For use with water up to 65°C.
Page 617 of 1013
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
