Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
'Welmortar-III'. Factory applied, grey coloured cement mortar. Mix cement, sand and water in a mass ratio of 2:3:0.85. Apply as per manufacturer's Standard Operating Procedure 'WDIPL/QA/WI/14A', revision '0', dated '01.10.2021'. Cure for 21 days at 30°C & 70% humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Sulphate Resisting Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/014', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RMD 7080/xx, RUD 2230/xx, RMD 7100/xx, RUD 2247/xx, RUD 2273/xx, RMD 7061/xx'. 'xx' denotes the customer and can be replaced with numbers between 01 & 99. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions '0703231010' dated 14.03.23. Cure for 10 minutes@860°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
ML-9005WGL414 (black coloured - RAL 9005), ML-6018WGL424 (green coloured - RAL 6018), ML-9A10WGL444 (white coloured - RAL 9010), ML-5007WGL424 (blue coloured - RAL 5007) & ML-6621WGL424 (green coloured - Pantone 334 C). Factory applied, electro-statically sprayed epoxy powder coatings. Apply as per manufacturer’s Product Data Sheet ‘Pdb_ML-WGL414-EN (03-2023)’, dated ’23.03.2023’. Stove (cure) for 8 minutes at 180°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KUBOTAPOWDER TK1413F M'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘KUBOTA SEAL AC’. Factory applied, colourless acrylic resin coating. Apply as per manufacturer’s instructions ‘ref. no. 65700H-2.3’ dated 'Mar. 14.2017'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Maxline 100 Potable Water Coating Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDSMLI100.rv5.04042023'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Vinoleo 77/14'. Amber coloured, soap based lubricant. Apply as per manufacturer's instructions. For use with water up to 23°C.
'PPELXS314G20NA'. Beige coloured, injection moulded PPE material. For use with water up to 85°C.
Page 58 of 120
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
