'KOCETAL GF305'. Off-white coloured, injection moulded POM material. For use with water up to 65°C.
'Seal Face PS5000'. Grey coloured, moulded and sintered silicon carbide washer. For use with water up to 85°C.
‘Series 2000 – Fusion Bonded Epoxy’. Factory applied, epoxy powder coatings available in the following colours: Code 29-0008: Description RAL9005 Black Deep FBE. Code 29-0008: Description RAL5015 Blue Sky. Code 29-0008: Description RAL5005 Blue Signal. Apply as per Powder-Lak (Pty) Ltd. technical information 'Rev.2,1 Q1 - 2021'. Cure for 10 minutes at 180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BFSC RIZHAO S&M&B DN 22'. Factory applied, grey coloured Blast Furnace Slag Cement Mortar Lining. Mix cement and sand in a weight ratio of 1:2.2. Mix this with water in a 0.46:1 weight ratio. Apply as per manufacturer's TDS '1008', dated '20221008'. Cure for 9 hours at 60°C & 95% humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SATHAVAHANA Ordinary Portland Cement'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a mass ratio of 1:1.5:0.5. Apply as per work instructions 'JSAW/AP01/DISP/PRO/WI-09', version '1.0', effective date '01.12.2022'. Cure for 3 hours at 45°C & 90% humidity. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SATHAVAHANA Sulphate Resistant Portland Cement'. Factory applied, grey coloured Sulphate Resistant Portland Cement. Mix cement, sand & water in a mass ratio of 1:1.5:0.5. Apply as per work instructions 'JSAW/AP01/DISP/PRO/WI-09', version '1.0', effective date '01.12.2022'. Cure for 3 hours at 45°C & 90% humidity. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SATHAVAHANA Portland Slag Cement'. Factory applied, grey coloured Portland Slag Cement. Mix cement, sand & water in a mass ratio of 1:1.5:0.5. Apply as per work instructions 'JSAW/AP01/DISP/PRO/WI-09', version '1.0', effective date '01.12.2022'. Cure for 3 hours at 45°C & 90% humidity. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JHSW-8604 Pipeline Heavy Duty Anti-Corrosion Polyurethane Coating'. Factory applied, two-component, pale yellow coloured polyurethane coating. Mix parts A & B in a 1:1 volume ratio and apply as per manufacturer's Product Information, issue date '6/1/2022'. Cure for 1 minute@25°C and then 7 days @23. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline DT-750'. Factory applied, grey coloured, two component epoxy coating consisting of a base and curing agent. Mix the base and curing agent in a 3:1 volume ratio. Cure for 7 days@25°C. For use with water up to 45°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VIMPOTABLE 34 EPOXY PAINT'. Factory applied, two-component, red coloured epoxy coating. Mix Parts A & B in a 3:1 volume ratio and apply as per manufacturer's Technical Bulletin 'VP/02', issue date '01.01.2021'. Cure for 7 days@50°C. For use with water up to 45°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 546 of 1111
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
