Range of pre-set pressure relief valves with brass or DZR brass bodies and EPDM diaphragms. The valves are fitted with hand operated easing gear. Pre-set pressure 3.0 bar for all models. Maximum operating temperature 85°C.
Range of normally closed (monostable) and pulse controlled/latching (bistable) solenoid valves with plastic bodies and integral stainless steel strainers. 50.005.101 model can also be supplied with an integral plastic strainer. To be installed in specifically dimensioned bodies. The 50.005.101 model can be supplied with or without a brass adaptor. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C. 50.009.101 Bistable is for cold water use only.
Flow through valve (chromium plated brass) for connection to expansion vessels. The product incorporates an isolation valve and a drain valve. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies (chromium plated), chromium plated brass balls, PTFE seat and single lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of gate valves with bronze bodies with metal seats. The valves operate via a non-rising spindle headworks that incorporate a wheel type operating member or lock shield type (see models). Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with bronze bodies with metal seats. The valves operate via a non-rising spindle headworks that incorporate a wheel type operating member or lock shield type (see models). Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The BT1405 & BT1406 models have a rising spindle, the BT1401 & BT1402 models have a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Angled servicing valves with chrome plated brass bodies incorporating dome type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of commercial dish washing machines. Flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure: 4.0 Bar. Maximum operating temperature: 60°C.
Range of water conditioners with stainless steel bodies. AFL012 MFB has a matt black finish and AFL012MFC has a chrome plate finish. Models with compression connections are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C.
Range of UV disinfection units with titanium bodies.
'HP204AD'. Grey coloured carbon bearing, pressed, sintered, impregnated with phenolic resin and rebaked. For use with water up to 85°C.
'JDFF-OPC-01'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a 1:2:0.50 weight ratio and apply as per manufacturers Work Instruction 'WI-Pc-01-5', 'Issue #: 5 Revision #: 1', dated '10.01.2025'. Cure for 48 hours@23°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
EUROKOTE® 711.92BF bleu 5012, EUROKOTE® 711.92BF bleu 5015, EUROKOTE® 711.92BF bleu 5005 CR, EUROKOTE® 711.92BF bleu 5005 & EUROKOTE® 711.92BF bleu 5017. EUROKOTE® 711.92BF noir 9005. EUROKOTE® 711.92 bleu 5012, EUROKOTE® 711.92 bleu 5015, EUROKOTE® 711.92 bleu 5005, EUROKOTE® 711.92 bleu 5005 CR & EUROKOTE® 711.92 bleu 5017. EUROKOTE® 711.92 noir 9005. EUROKOTE® 711.92 BF Brun Rouge & 711.92 Brun Rouge Factory applied, blue, black or red coloured epoxy coatings. Apply as per manufacturer's technical data sheets dated 04/03/2025. Cure for 2 minutes@200°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Endolac® 245.10'. Factory applied, black coloured bituminous paint. Apply as per manufacturer's TDS 'Version edit: 17/04/2024'. Cure for 7 days at 20°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER CM-4'. Factory applied, grey coloured Portland Cement. Mix sand, cement and water in a 40:20:40 weight ratio and apply as per manufacturer's instruction sheet 'Revision: A1', dated '2023-11-15'. Cure for 4 hours at 23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL 83275'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's TDS 'TDS-2025-AL83275-REV00', dated '03.07.2025'. Cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 544 of 578
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
