'Loctite EA 9480'. Site applied, two-component, white coloured (once mixed) epoxy adhesive. Mix and apply as per manufacturer's technical data sheet dated October 2014. Cure for 7 days@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Novodur® SBM-90 Q203'. Natural (appears off-white), injection moulded thermoplastic resin. The natural material may be coloured using the following INEOS Styrolution colourants at the agreed maximum percentage concentrations by weight: Pigment White 6, Black 7, Blue 15:3, Blue 29, Brown 24, Red 101, Violet 15, Green 7, Green 17 & Yellow 53. For use with water up to 60°C.
'Novodur® SBM-90'. Natural (appears off-white), injection moulded thermoplastic resin. The natural material may be coloured using the following INEOS Styrolution colourants at the agreed maximum percentage concentrations by weight: Pigment White 6, Black 7, Blue 15:3, Blue 29, Brown 24, Red 101, Violet 15, Green 7, Green 17 & Yellow 53. For use with water up to 60°C.
Deck mounted single hole, single outlet (fixed) electronically controlled tap assembly (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Tempearture is controlled from a separate control unit incorporating a thermostatic cartridge, which is operated by a single lever on the side of the unit. The spout connects to the unit via a (transparent) PEX-b pipe. The inlets of the control unit incorporate a stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the unit incorporates a plastic flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns with a side entry BS 1212-4(2016) float operated inlet valve providing a type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two button assembly for a 6 or 3 litre flush volume. The cistern incorporates a servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. Maximum working pressure 10.0 Bar, Cold Water use only
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Non-verifiable single check valve assembly consisting of a spring loaded, resilient trim, single check valve cartridge with a brushed chrome DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of single check valve assemblies incorporating DZR brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Non- verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a chrome plated DZR brass body with an integral insolation valve between the cartridges. For use with copper pipes to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies (DZR brass bodies) incorporating spherical valves and either red or blue butterfly handles. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks incorporating NBR ‘O’ rings and silicone seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks incorporating brass bodies and NBR ‘O’-rings. For insertion into any specifically dimensioned tap assemblies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc and cartridge headworks with plastic bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
A range of ceramic cartridge headworks with plastic bodies incorporating EPDM `O`-rings and seals for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Thermostatic cartridge incorporating brass body (chrome plated), stainless steel strainers and EPDM ‘O’-rings. For insertion into specifically dimensioned tap bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of thermostatic cartridges incorporating plastic bodies, stainless steel filters and EPDM ‘O’-rings. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
A range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated), incorporating a ceramic cartridge headwork (models 63465-0001) or a quarter turn ceramic disc headwork (model 63461-0001) with single lever operating members. The products incorporate a pull-out spray with a plastic aerator at the outlet. The pull-out spray hose for model 63465-0001 incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes ), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Fittings are supplied with click type wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 51 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
