Range of brass and copper end feed fittings for use with copper pipe (manufactured to EN 1057). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

251202002

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models

Marking:

Endex and size on body of fitting

Installation Requirements:

R001

Expiry date:

31/12/2030

Model:

N6 - Reducer, larger end male - 88310 (66.7 x 28mm), N6 - Reducer, larger end male - 88311 (66.7 x 35mm), N6 - Reducer, larger end male - 88312 (66.7 x 42mm), N6 - Reducer, larger end male - 88313 (66.7 x 54mm), N6 - Reducer, larger end male - 89624 (76.1 x 35mm), N6 - Reducer, larger end male - 89625 (76.1 x 42mm), N6 - Reducer, larger end male - 89626 (76.1 x 54mm), N6 - Reducer, larger end male - 89630 (108 x 42mm), N6 - Reducer, larger end male - 89631 (108 x 54mm), N6 - Reducer, larger end male - 89699 (133 x 42mm), N6 - Reducer, larger end male - 89700 (133 x 54mm), N6 - Reducer, larger end male - 89704 (159 x 54mm), N25 - Tee, reduced branch - 88807 (66.7mm x 28mm), N25 - Tee, reduced branch - 89055 (66.7mm x 35mm), N25 - Tee, reduced branch - 89056 (66.7mm x 42mm), N25 - Tee, reduced branch - 89057 (66.7mm x 54mm), N25 - Tee, reduced branch - 89058 (76.1mm x 28mm), N25 - Tee, reduced branch - 89000 (76.1mm x 35mm), N25 - Tee, reduced branch - 89654 (76.1mm x 42mm), N25 - Tee, reduced branch - 89001 (76.1mm x 54mm), N25 - Tee, reduced branch - 89059 (108mm x 35mm), N25 - Tee, reduced branch - 89660 (108mm x 54mm), N25 - Tee, reduced branch - 89715 (133mm x 54mm), N25 - Tee, reduced branch - 89717 (159mm x 54mm),

Approval Holder:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Country

United Kingdom

Phone

+447843075405

General Email

gavin.peters@aalberts-ips.com

View All Listings by this Company

Type ‘J’ range of plate heat exchangers with stainless steel (AISI 304L or AISI 316L) fin and end plates. Maximum working pressure 3.0 bar (primary circuit) and 10.0 bar (secondary circuit). Maximum operating temperature 80°C.

Section:

1350 Heat Exchangers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M) Primary circuit. ½” BSP (M) Sanitary circuit.

Marking:

Condevo S.p.A. and model on adhesive label on body

Installation Requirements:

R001

Expiry date:

31/01/2031

Model:

Type ‘J’ range comprising of: PP10FJX. PP12FJX. PP14FJX. PP16FJX. PP18FJX. PP20FJX. PP22FJX. PP24FJX. PP26FJX. PP28FJX. PP30FJX. PP32FJX. PP34FJX. X denotes the body material and is replaced with: 4 = AISI304L 6 = AISI316L

Approval Holder:

Condevo SpA

Company Name

Condevo SpA

Address

Via Luna, Z.A. 26866 Marudo (LO) Italy

View All Listings by this Company

Range of pressure transmitters with stainless steel bodies. Maximum working pressure 100.0 Bar Maximum operating temperature 80.0°C (Type 540) or 100.0°C (Type 520 & Type 522)

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See Models

Marking:

Huba Control logo and technical info on body

Installation Requirements:

R001

Expiry date:

31/01/2031

Model:

Type 520: Dimension, Sealing type, Male/Female Thread 7/16"-20 UNF, sealing cone 45°, Female 7/16"-20 UNF, sealed at front ISO 11926-1 Male G1/4", sealed at front, Female 1/2"-14 NPT, thread sealing, Male 1/2"-14 NPT, thread sealing, Female 7/16"-20 UNF, sealing cone 45°, Male G1/8", sealed at front, Male G1/4", sealed at back without sealing groove, Male G1/4", sealed at back ISO 1179-2, Male G1/4", sealed at back + Manometer, Male G1/4", sealed at front, Female G1/4", sealed at front + Manometer, Male G1/4", sealed at back DIN 3852-2, Male R1/4", thread sealing EN 10226, Male G1/2", sealed at front, Male M20x1.5, sealed at front + Manometer, Male 7/16"-20 UNF, sealing cone with schrader, Female Type 522: Dimension, Sealing type, Male/Female Thread 7/16"-20 UNF, sealing cone 45°, Female 1/2"-14 NPT, thread sealing, Female 7/16"-20 UNF, sealing cone 45°, Male G1/4", sealed at back ISO 1179-2, Male G1/4", sealed at back + Manometer, Male G1/2", sealed at front, Male G1/2", sealed at front + Manometer, Male M20x1.5, sealed at front + Manometer, Male Type 540: Dimension, Sealing type, Male/Female Thread G1/4", sealed at front, Female 7/16"-20 UNF, sealing cone 45°, Male G1/4", sealed at back ISO 1179-2, Male R1/4", thread sealing EN 10226, Male Additional Information The pressure orifice and the connectors are all made from stainless steel X2CrNiMo17-12-2/1.4404 / AISI316L. The Schrader is made from Stainless X8CrNi18-9/1.4305/303 All variants can use the following pressure cell options, based on application requirements: -1…9 Bar / 0…2.5 - 100 bar (Stainless Steel Cell X6Cr17-1.4016) The only difference between the models 520, 522 & 540 is the input and output signal, and the approvals (not relevant to WRAS) All the different type variants can be given a unique customer article number, to trace the full specification: Example: 520.99XXX 520 = Model Type 99 = Client / project specific number XXX = Unique file for client containing all the above options specified within model.

Manufacturer:

Huba Control AG

Company Name

Huba Control AG

Address

Industriestrasse 17, CH-5436 Wurenlos, Switzerland

View All Listings by this Company

Range of electric water pumps, with stainless steel bodies, shaft and either stainless steel or plastic impellors. Maximum working pressure 8.5 Bar. Maximum operating temperature: See models.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

251202728

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1” BSP (F)

Marking:

Felsom, model and technical data on data plate on body

Installation Requirements:

R001

Expiry date:

31/12/2030

Model:

U 3A-90/4; U 3A-100/5 - 35 °C U 3A-90/4 T; U 3A-100/5 T - 35 °C U 5A-120/4 ; U 5A-150/5 - 35 °C U 5A-120/4 T; U 5A-150/5 T - 35 °C U 3SA-90/4; U 3SA-100/5 - 80 °C U 5SA-120/4; U 5SA-150/5 - 80 °C U 3SA-90/4 T; U 3SA-100/5 T - 80 °C U 5SA-120/4 T; U 5SA-150/5 T - 80 °C

Product Images

Approval Holder:

Exa Pumps SrL

Company Name

Exa Pumps SrL

Address

Via Tre Confini, 23 22010 Gera Lario CO

Country

Italy

Phone

0039 0344 910054

General Email

infor@exapumps.com

View All Listings by this Company

MBC 12-22WM & MBC 12-28WM models are wall mounted mains supply booster sets. They are supplied with two spherical isolation valves, a spherical bypass valve and two single check valve assemblies (suitable for backflow protection against Fluid Category 2). The check valve assemblies are to be installed in accordance with the manufacturers instructions, one upstream of the pump inlet and one after the bypass valve. The booster pump incorporates a plastic strainer on the inlet and a plastic flow regulator on the outlet and is housed within a wall mounted cabinet. MJ3 VM & MJ3 HM models are mains supply booster sets intended to be mounted on an expansion vessel (not supplied as part of the approval). They comprise of a pump, a suction and discharge manifold with bypass arrangement, and a spherical bypass valve which incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The booster pump incorporates a plastic strainer on the inlet and a plastic flow regulator on the outlet. Maximum working pressure: 6.0 bar. Maximum operating temperature: 35oC.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

251208701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

MBC 12-22WM & 12-28WM models: Quadruple layered flexible hoses consisting of a black coloured TPE inner layer, PVC middle layer, braided PE third layer and white coloured PVC outer layer with 15mm pushfit end connections. MJ3 VM & HM models: Stainless steel braided EPDM lined flexible hose assemblies with 22mm pushfit end connections.

Marking:

Stuart Turner, Stuart Turner logo, mains boost, model no., pressure, temperature and other technical information on adhesive label on pump. Stuart Turner on pump body.

Installation Requirements:

R001 R415

Expiry date:

31/12/2030

Model:

Part code 44725: Mainboost charger MBC 12-22WM. Part code 44726: Mainboost charger MBC 12-28WM. Where: MBC = Range name: Mainsboost Charger. 12 = maximum pumped flow in l/min. 22 or 28 = 22mm or 28mm sizes bypass fittings supplied. WM = wall mounted. Part code 41712: Mainboost charger MJ3 VM. Part code 41729: Mainboost charger MJ3 HM. Where: MJ = MJ pump, version 3. VM = vertical vessel mounted. HM = horizontal vessel mounted.

Approval Holder:

Stuart Turner Ltd

Company Name

Stuart Turner Ltd

Address

47 Market Place Henley-on-Thames Oxfordshire

Postcode

RG9 2AD

Country

United Kingdom

Phone

01491 572655

General Email

stuart.savill@stuart-turner.co.uk

View All Listings by this Company